manualshive.com logo in svg

Lucent Technologies PARTNER Advanced Communications System Release 1.0, Programming And Use Instructions

Share
Download
Lucent Technologies PARTNER Advanced Communications System Release 1.0 Programming And Use Instructions Download Page 243

Using

(See Figure 2-3 in Chapter 2 for the location of special programming buttons
such as 

s

 and 

e

 on system phones.)

To initiate a restore:

1.

Power down the system:

If you have a 5-Slot carrier, move the On/Off switch to the “Off” position
(“O”). 

If you have a Stand-Alone PARTNER ACS processor module
configuration or a 2-Slot carrier, unplug the power cord from the power
jack.

2.

Insert the correct Backup/Restore PC Card in Slot 2 of the PARTNER ACS
processor module; if there is a PC Card in Slot 1, remove it.  (If the system
detects cards in 

both slots, it will use Slot 1 for the Restore.)

3.

Power up the system:

If you have a 5-Slot carrier, move the On/Off switch to the “On” position
(“I”).

If you have a Stand-Alone PARTNER ACS processor module
configuration or a 2-Slot carrier, plug the power cord into the power
jack.

4.

Press

 f 0 0 s s # 1 2 5

 at extension 10

or 11.
The top line of the display shows 

Sys Set Restore

 or 

System

Settings Restore

.

If no PC Card is present in the PARTNER ACS processor module, the error
message 

Insert Valid Card

 is displayed. Repeat this procedure from

Step 1, inserting a Backup/Restore PC Card at Step 2.  

You must power

down the system  before removing or inserting a Backup/Restore PC
Card. 

 

You are prompted to choose the backup file you want to use for the
restore. The bottom line of the display shows 

1 MAN.mmddyy

, where

mmddyy

 represents the date of the manual backup on this card.

5.

To change to the file created by an automatic backup, press 

2

.

The bottom line of the display shows 

2 AUTO.mmddyy,

where

 mmddyy

represents the date of the automatic backup on this card.

NOTE:

If the date of the file (AUTO.

mmddyy or MAN.mmddyy) indicates that this

is not the file you intended to use, repeat this procedure from Step 1 and
insert a different Backup/Restore PC Card in Step 2.  

You must power

down the system  before removing or inserting a Backup/Restore PC
Card. 

 

If the Backup/Restore PC Card is fresh from the factory, and no backups
have been recorded on it yet, the filenames will be 

MAN.******

 and

5-150    

Restore Programming (#125)

Summary of Contents for PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands