Lucent Technologies PacketStar PSAX 45N74 User Manual Download Page 4 | Manualshive

Page: 4 / 104

background image

Legal Notices, Safety, and Regulatory Information

Safety Warnings and Information

iv

255-700-585

PacketStar

®

PSAX 3-Port DS3/E3 ATM Protection Module User Guide

, Issue 1

Release 10.0.0

Warranty Warnings

WARNING:

!

When inserting modules into the chassis, slide them gently, not force-
fully. Excessive force may cause the modules to be seated improperly in
the chassis, and result in possible damage to the module or the chassis.
Install or remove modules one at a time. Doing this aids in preventing
the PSAX system from indicating any erroneous failure messages, and
allows the PSAX system time to reinitialize and display the accurate con-
figuration of the module that is inserted.

!

CAUTION:

Modifying or tampering with PSAX chassis components may void your
warranty. Any modification to this equipment not expressly authorized
by Lucent Technologies may void your granted authority to operate such
equipment.

!

CAUTION:

Shipping the chassis with removable I/O, server, or CPU modules
installed may cause damage to the chassis and the modules. Damage to
any of the components in the system resulting from shipping the chassis
with removable modules installed will void your warranty.

Safety Warnings and Information

When installing and operating the 3-Port DS3/E3 ATM Protection module,
follow the safety guidelines provided in the

PacketStar

®

PSAX Multiservice

Media Gateway Safety Guidelines

, which accompanies this product, to help pre-

vent serious personal injury and damage to the module. Please read all warn-
ings and instructions supplied before beginning installation or configuration
of this module. In addition to the general safety information provided, you
should also refer to the appropriate PSAX installation guide for other impor-
tant safety information and procedures.

Regulatory Standards Compliance

Safety and Electromagnetic Compatibility (EMC)

The following

PacketStar

PSAX systems are compliant with applicable safety

and EMC standards when configured with the 3-Port DS3/E3 ATM Protec-
tion module (model 45N74):

•

PSAX 1000 system

•

PSAX 4500 system

Refer to the

PacketStar

PSAX 1000 or PSAX 4500 Multiservice Media Gate-

way installation guide for details on safety and EMC standards compliance.

«
...
2
3
4
5
6
...
»

Summary of Contents for PacketStar PSAX 45N74









































































































Reviews:

No comments

Related manuals for PacketStar PSAX 45N74

Brand: Vacon Pages: 62

Brand: FAAC Pages: 12

Evolution Series E9000

Brand: GE Pages: 44

PACSystems RX7i

Brand: GE Pages: 469

GuardSwitch 300 Series

Brand: GE Pages: 2

GuardSwitch 300 Series

Brand: GE Pages: 2

Masoneilan VariPak 28001

Brand: GE Pages: 24

Brand: Panasonic Pages: 45

Brand: TCS Basys Controls Pages: 2

Brand: Datavideo Pages: 17

Brand: Datamax Pages: 22

ServeRAID-MR10is

Brand: IBM Pages: 94

ServeRAID-4 Ultra160 Series

Brand: IBM Pages: 20

8271 Nways Ethernet LAN Switch

Brand: IBM Pages: 6

Brand: IBM Pages: 86

Brand: IBM Pages: 205

Brand: IBM Pages: 28

Brand: Objective Imaging Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands