manualshive.com logo in svg

Lucent Technologies J85501E-1, Product Manual, Page: 53 / 95

Share
Download
Lucent Technologies J85501E-1 Product Manual Download Page 53

Lucent Technologies Lineage

®

 2000 ECS-6U Controller J85501E-1

4 - 16  Installation and Setup 

 Issue 4  August 1998

Optional

Rectifier Adapter

Board (RAB)

The Rectifier Adapter Board (RAB) may be added to the 
controller to extend the features described in this manual to 
pre-Lineage

®

 rectifiers either manufactured by Lucent 

Technologies or manufactured for Lucent Technologies to a J or 
KS specification. (See Figure 4-11.) DIP switches S1 through S6 
on the RAB must be set corresponding to the port used for each 
non-Lineage

®

 rectifier connected to the controller. (See Figure 

4-12.) Table 4-D lists the cables required for the various 
rectifiers. Those rectifiers not listed will require a termination 
either to a screw or wire wrap terminal at the rectifier end. See 
Table 4-E and Figure 4-10.

The RAB also permits non-Lucent Technologies rectifiers to be 
used with the controller. DIP switches S1 through S6 on the 
RAB must be set corresponding to the port used for each of the 
non-Lineage

®

 rectifiers connected to the controller. For 

rectifiers not manufactured by Lucent Technologies, the cable 
will always require field termination to a wire wrap or screw 
terminal. See “Mixed Types of Rectifiers in One Plant” in 
Section 2.

A rectifier must have a feature in order for the ECS-6U to extend 
that feature to the system. For example, if a rectifier is not 
capable of acting upon an automatic restart signal, the rectifier 
will not restart even though the controller sends the signal to the 
rectifier.

The RAB is required for all Lucent Technologies non-Lineage

®

 

2000 rectifiers and all rectifiers not manufactured by Lucent 
Technologies. 

Figure 4-12: RAB DIP Switch Settings

EAT2 DIP SWITCH SETTINGS - S1 THRU S6

RECTIFIER OPTIONS

(NON-LUCENT RECTIFIERS ONLY)

SWITCH POSITION

*

*

*

*

*

*

1 THRU 8

ON

OFF

-

-

-

-

9

-

-

ON

OFF

OFF

ON

10

-

-

OFF

ON

ON

OFF

24V

48V

ALARM = OPEN

ALARM = CLOSURE

ALARM NOT PROVIDED

NO RECTIFIER

VOLTAGE

MAN

ALARM

ALL SWITCHES MUST BE SET

ACCORDING TO THIS TABLE.

SETTINGS TO BE USED WHEN

NO RECTIFIER OR A LUCENT
RECTIFIER IS CONNECTED TO
THE CORRESPONDING PORT.

-

-

NOTE:

OFF=OPEN

ON=CLOSED

Summary of Contents for J85501E-1
































































































Reviews:

No comments