Lucent Technologies CellPipe 60A User Manual Download Page 68

Page: 68 / 70

68 CellPipe® 60A/60A-BX User Guide

Software Specifications

ATM

•

ATM Cell over ADSL, AAL5

•

Support UBR, CBR, & VBR-nrt

•

VPI Range (0-4095) and VCI range (1-65535)

•

Supports up to 8 PVCs in Bridge mode and 5 PVCs in Router mode

•

Supports OAM F4/F5 loopback

•

Payload Encapsulation

−

RFC2684 (RFC1483), multi-protocol over ATM

−

RFC2225 (RFC1577), IPoA

−

RFC2364, PPP over ATM (CHAP and PAP supported)

−

RFC2516, PPPoE (PPP over Ethernet) over ATM

Bridging

•

Transparent Bridging (IEEE 802.1D)

•

RFC2684 (RFC1483) Bridged

•

Spanning Tree Protocol (IEEE 802.1D)

•

Supporting IP, IGMP, and PPPoE packets filter function

Routing

•

TCP/IP with RIP1, RIP2 routing, or static IP routing

•

NAT/PAT – RFC1631

•

RFC2684 (RFC1483) Routed

•

DNS relay

Configuration and Network Management

•

DHCP server for IP management

•

Telnet for local or remote management

•

TFTP for firmware upgrade

•

WEB configuration

Firewall

•

C NAT

•

Port filter

•

IP filter

•

IDS

Summary of Contents for CellPipe 60A







































































Search results

Summary of Contents for CellPipe 60A

Reviews:

Related manuals for CellPipe 60A

Brands by name

Popular brands

Lucent Technologies CellPipe 60A, User Manual

Search results

Summary of Contents for CellPipe 60A

Reviews:

Related manuals for CellPipe 60A

Brands by name

Popular brands