Lucent Technologies CAJUN M770 User Manual Download Page 81

Page: 81 / 266

Chapter 6

Managing Virtual Ports

Cajun M770 ATM Switch User’s Guide

Setting the QSAAL wait parameter on a virtual port

This parameter changes this vport to wait indefinitely for an incoming QSAAL
connection. By default, this parameter is disabled.

To set the waitqsaal parameter on the virtual port use the

vport set waitqsaal

command.

Note:

Before any virtual port parameters can be changed or reset, you must disable

the virtual port. For more information about how to disable a virtual port, see
Disabling a virtual port earlier in this chapter.

Command:

M15-155s8:/>vport set waitqsaal <vport id> [on|off]

Example:

M15-155s8:/>vport set waitqsaal 8.1.0 on

Parameters:

The virtual port in the form
<slot>.<port>.<virtual port number>.

[on|off]

Turns waitqsaal parameter On or Off.

Summary of Contents for CAJUN M770











































































































































































































































































Search results

Summary of Contents for CAJUN M770

Reviews:

Related manuals for CAJUN M770

Brands by name

Popular brands

Lucent Technologies CAJUN M770, User Manual

Search results

Summary of Contents for CAJUN M770

Reviews:

Related manuals for CAJUN M770

Brands by name

Popular brands