LSI DMN-8600 Technical Manual Download Page 298 | Manualshive

Page: 298 / 434

background image

LSI Logic Confidential

15-88

Serial I/O Port

Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.

When changing from FIFO mode to NS16450 mode and
vice versa, data is automatically cleared from the FIFOs.
This bit must be 1 when other FCR bits are written to, or
they will not be programmed. If the user wishes to have
the DMA Engine automatically fill/drain the UART FIFOs
with data, then this bit must be set to 1 to have the FIFOs
enabled in the first place.

By default, non-FIFO mode is enabled.

UART1 Line Control Register (UART1_LCR)

UART2 Line Control Register (UART2_LCR)

Offset = 0xBE010C / 0xBE018C

Read/Write

Default = 0x0000 0000

The UART is configured to operate as follows:

•

Transmit 5 bits/character and 1 stop bit

•

Parity disabled

•

Odd parity selected

•

SP is 0, SB is disabled, DLAB is 0

which means that the first access to the DLL-THR-RBR and the DLM-
IER registers will not be to baud generator registers.

DLAB

Divisor Latch Select

31

1 = Select the divisor latches to be accessed during
read/write operations to the DLL-THR-RBR and the DLM-
IER registers.

SB

Set Break

30

1= The SOUT pin goes low.

31

30

29

28

27

26

25

24

23

16

DLAB

SB

SP

EPS

PEN

STB

WLS1

WLS0

RSVD

15

0

RSVD

«
...
296
297
298
299
300
...
»

Summary of Contents for DMN-8600



















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DMN-8600

Brand: Tascam Pages: 20

Brand: Sylvania Pages: 62

Brand: SpyCameraCCTV Pages: 2

Brand: Olympus Pages: 2

Brand: Pye Video Pages: 83

Brand: ABB Pages: 2

Brand: Olympus Pages: 2

Brand: Panasonic Pages: 141

Brand: Night Owl Pages: 80

Brand: GGKaiser Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands