LSI DMN-8600 Technical Manual Download Page 177 | Manualshive

Page: 177 / 434

background image

DMN-8600 DVD Recorder System Processor

13-1

Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.

LSI Logic Confidential

Chapter 13
SDRAM Interface

This chapter describes the SDRAM interface and contains the following
sections:

•

Section 13.1, “DRAM Address Map”

•

Section 13.2, “DRAM Address Field Description”

•

Section 13.3, “Supported Number of Simultaneous Banks”

•

Section 13.4, “SDRAM Initialization”

•

Section 13.5, “SDRAM Refresh”

•

Section 13.6, “External SDRAM Configuration Register”

•

Section 13.7, “SDRAM Control and Clock Control Registers”

•

Section 13.8, “SDRAM Arbitration and Throttle Registers”

•

Section 13.9, “SDRAM Timing”

The DMN-8600 processor uses a 32-bit memory interface that supports
up to 64 Mbytes of DRAM. The DRAM memory uses two to four 16-bit
wide SDR/DDR DRAMs, or one to two 32-bit wide SDR/DDR DRAMs,
capable of running at 150 MHz, 2.5 V–3.3 V. SDRAM_RAS and
SDRAM_CAS latency and cycle times are programmable to allow for
DRAMs from different vendors at different speeds to be used.

The DMN-8600 supports the following DRAM types, with parameters
listed in Table 13.1:

•

8 Mbytes to 64 Mbytes

•

Three types of DRAM:

–

Single Data Rate Synchronous DRAM (SDR-SDRAM)

–

Double Data Rate Synchronous DRAM (DDR-SDRAM)

–

Double Data Rate Synchronous GRAM (DDR-SGRAM)

«
...
175
176
177
178
179
...
»

Summary of Contents for DMN-8600



















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DMN-8600

Brand: Mini Gadgets Pages: 5

Brand: ABB Pages: 8

Commander C1900

Brand: ABB Pages: 20

Brand: Aiwa Pages: 2

Brand: Olympus Pages: 64

Brand: Sangean Pages: 9

Brand: Olympia Pages: 56

Brand: Sangean Pages: 42

Brand: Olympus Pages: 113

WS-321M - 1 GB Digital Voice Recorder

Brand: Olympus Pages: 2

Brand: Radio Shack Pages: 28

Brand: Magnavox Pages: 2

Brand: M-system Pages: 25

Brand: Philips Pages: 20

POCKET MEMO LFH9380/01

Brand: Philips Pages: 30

Brand: JVC Pages: 49

Brand: JVC Pages: 54

Brand: JVC Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands