LSI LASTEM Alpha-Log User Manual Download Page 103

Page: 103 / 116

Alpha-Log

–

User manual

LSI LASTEM SRL

INSTUM_03388

Page 103 / 116

Alpha-Log configuration templates

Type 1 configuration: Alpha-Log + ALIEM

Alpha-Log

Sensor

Quantity

DQA230.1

Rain

DMA672.1

TempUR

DLE041

Ground temperature

DQA340

Water content

Pressure (internal)

Temperature (internal)

ALIEM

Sensor

Quantity

DNA121

Wind Speed+Dir

DPA154

Global Rad.

DQC102

Evaporation

DLE124

Contact temperature

DQC001.15

Water level

Sensor
code

Measure (UM)

Acq. rate
hh:mm:ss

Elaborations
(rata hh:mm

–

tipo)

Alpha-Log
input

DQA230

RAIN (mm)

00:01:00

00:10

–

Tot

01:00

–

Tot

24:00

–

Tot

Last 10 min

–

Mobile tot

Last 60 min

–

Mobile tot

Pulse/Freq1

DMA672.3

Temperature (°C)

00:01:00

00:10 - Min, Med, Max, DevStd
01:00 - Min, Med, Max, DevStd
24:00 - Min, Med, Max, DevStd

TTL Serial

RelHumidity (%)

00:01:00

00:10 - Min, Med, Max, DevStd
01:00 - Min, Med, Max, DevStd

DLE041

Temperature (°C)

00:01:00

00:10 - Min, Med, Max, DevStd
01:00 - Min, Med, Max, DevStd
Last 60 min

–

Mobile med

Pt100

DQA340

VolMoisture (%)

00:01:00

00:10 - Min, Med, Max, DevStd
01:00 - Min, Med, Max, DevStd

Analog In

SOILTemp (°C)

00:01:00

00:10 - Min, Med, Max, DevStd
01:00 - Min, Med, Max, DevStd
Last 60 min

–

Mobile med

AtmPres (hPa)

00:01:00

00:10 - Min, Med, Max, DevStd
01:00 - Min, Med, Max, DevStd

On board

INSideTemp (°C)

00:01:00

00:10 - Min, Med, Max, DevStd
01:00 - Min, Med, Max, DevStd

On board

Summary of Contents for Alpha-Log





















































































































Search results

Summary of Contents for Alpha-Log

Reviews:

Related manuals for Alpha-Log

Brands by name

Popular brands

LSI LASTEM Alpha-Log, User Manual

Search results

Summary of Contents for Alpha-Log

Reviews:

Related manuals for Alpha-Log

Brands by name

Popular brands