installation tips
wires & installation
connections & explanations
user manual
specifications
radio- / speed-control setup
spare- & optional-parts
A
B
C
+ -
C
B
A
orange
blue
yellow
Hall Sensor Wire
Receiverwire
On/Off - Switch
M
O
T.
C (
Or
an
ge
)
Power Capacitor
BA
T + (
Re
d)
M
O
T.
B (
Ye
llo
w
)
BA
T - (
Bl
ac
k)
M
O
T.
A (
Bl
ue
)
Hall Sensor Connector
• Position the speed-control and capacitor where they are protected in the event of a crash and gives you easy
access to the connectors and buttons.
• Mount the speedo and capacitor using the supplied thick/black doubled-sided tape
• Make sure there is enough clearance between the speed-control, power-wires, antenna and receiver. Avoid
any direct contact between power components, the receiver or the antenna as this can cause interference. If
interference occurs, position the components at a different place in the model.
• The aerial should be run vertically up and away from the receiver. Avoid contact with any parts made of carbon
fibre or metal. If the aerial is too long, don’t coil up the excess length. See also the instructions supplied with
your radio control system.
Receiver Connecting Wire:
The
SPX Zero
is equipped with an LRP Multicon receiver wire. As supplied, it will
easily fit in all ordinary receivers. Make sure you connect it to receiver with correct polarity and use channel 2.
Sensor Connector:
The bi-directional multipole sensor wire connects the speed-control and the motor. Always
use the sensor wire and do not alter or modify this cable! There are replaceable/optional hall sensor wires available,
please refer to complete line-up at „Spare- & Optional-Parts“.
Power Wires:
For maximum performance, flexible silicone power wires without any connectors are used. The
unique splitted solder-tabs allow easy and convenient replacement of the power wires. Nevertheless some sol-
dering skills are required. Avoid soldering longer then 5sec per soldering joint to prevent possible damage to the
speed-control due to overheating of the components! There are replacement power wires available, please refer to
complete line-up at „Spare- & Optional-Parts“.
Pure Brushless
yes
BEC
6.0V/3.0A
Forward/Brake
yes
High Frequency
yes
Size
33.1x37.6x14.9mm
Sensored Brushless System
yes
Weight (excl. wires)
24.5g
Multi-Protection-System
yes
Voltage Input
4.8-7.4V
Internal-Temp-Check System
yes
Typ. Voltage Drop* @20A
0.026V / phase
„Boost 0“ Mode
yes
Rated Current*
200A / phase
Power Wires
2.6mm²
Compatible winding styles
Star
4 adj. Modes (ACS, Powerprofiles,
Initial- and Autobrake)
yes
Rec. Motor Limit with 2S LiPo
over 7.5T
The
SPX Zero
comes supplied with flexible 2.6mm² silicone power-wires without connectors. Be very careful with
the correct wire sequence/colors since an incorrect connection may damage the speed-control! Avoid creating
solder bridges on the solder-tabs and isolate all connections carefully.
Caution:
Avoid soldering longer then 5sec per soldering joint when replacing the power wires on the speed-control
and motor to prevent possible damage due to overheating of the components!
• Connect the speed-control to the receiver (position: Channel 2
• Blue power-wire
Speedo MOT.A to motor „A“
• Yellow power-wire
Speedo MOT.B to motor „B“
• Orange power-wire
Speedo MOT.C to motor „C“
• Connect the hall sensor cable to the speed-control and the motor.
• Doublecheck all connections before connecting the speed-control to a battery.
CAUTION:
If battery is connected with reversed polarity it will destroy your speed-control!
• Red power-wire
Speedo BAT+ to battery „Plus“
• Black power-wire
Speedo BAT- to battery „Minus“
• The speed-control is now ready to be set-up (see section „Radio-/Speed-Control Setup)
RA00294
* Transistors rating at 25°C junction temperature Specifications subject to change without notice.
LRP electronic GmbH
Wilhelm-Enssle-Str. 132-134
73630 Remshalden, Germany
[email protected] - www.LRP.cc
Dear Customer,
thank you for your trust in this LRP product. By purchasing a
LRP SPX Zero
brushless speed-control, you have
chosen a highly advanced product aimed for true stock brushless racing. This speed-control with all of its high-
tech features and specially selected electronic components is one of the best speed-controls currently available
on the market.
• „Boost 0“ Mode for true stock racing
• 100% Brushless Forward/Brake
• Add. profiles for many classes
• Advanced Digital
• Internal-Temp-Check system
• AutoCell System
• Sensored Design
• 2.6mm² Power-Wires
• Multi-Protection System 3
• Small footprint
Please read the following instructions carefully before you start using your speed control. This user guide contains
important notes for the safety, the use and the maintenance of this product. Thus protecting yourself and avoid damages
of the product.
Proceed according to the user guide in order to understand your speed control better. Please take your time as you will
have much more joy with your product if you know it exactly.
This user manual shall be kept in a safe place. If another customer is using this product, this manual has to be handed
out together with it.
In setup mode the
SPX Zero
stores every step (e.g. learning your radios neutral and endpoints) by pressing the SET
button. All the settings will be stored in the memory even if it will be disconnected from the battery.
Description
other names in radio
Required Setting
Throttle Travel
High ATV, EPA
100%
Brake Travel
Low ATV, EPA, ATL
100%
Throttle Exponential
EXP, EXPO
start with 0
Neutral Trim
SUB Trim
centre
Servo Reverse
Throttle Reverse
any setting, don‘t change after set-up procedure!
TRANSMITTER SETTINGS:
Setup the following basic functions on your transmitter (if available):
If your transmitter doesn‘t offer any of above functions, it‘s already in „basic setup“ mode.
• Ensure that the speed-control is not connected to the drive battery and is switched off.
• Remove motor pinion or ensure that the wheels of the model are free to rotate.
• Switch the transmitter on and set the transmitter throttle stick to neutral.
• Connect the speed-control to the battery and switch the unit on.
• Hold the SET button pressed for at least 3sec.
You entered setup mode and the SET LED flashes red (it will flash until the setup is completed).
• Leave transmitter in neutral position and press the SET button once.
Neutral setting is stored , MODE LED flashes green and the motor beeps.
• Hold full throttle on transmitter and press the SET button once.
Full-throttle setting is stored, MODE LED flashes red.
• Hold full brake on transmitter and press the SET button once.
Brake setting is stored, LED‘s glow red (MODE) and red (SET).
• This completes the setup procedure and your
SPX Zero
is ready to use.
• If you make a mistake during the setup procedure, don‘t worry: Disconnect the battery for about 10sec and start
again from the first step.
• At the end of each run switch of the car, and then switch off the transmitter.
• At the start of each run switch on the transmitter first, then switch on the car.
• For storage of the car, disconnect the drive battery at any time!
Function
Status
Mode LED
Set LED
Neutral
--
off
red
Neutral (when „Boost 0“ selected)
--
flashes red
Forward
partial throttle
green
off
full
red
Brake
partial brake
red
off
full
red
CHECKING THE FUNCTIONS:
Check the LED‘s when moving your throttle stick and you will see if everything is
setup correctly.
© lrp electronic GmbH 2010
order.no.:
80705
sensored Brushless speed-control
for true stock racing
„Boost 0“ mode
>7.5t motorlimit
LRP offers a comprehensive line of accessories, as well as particular spare- and optional items. Here you find an
overview, for a full picture please visit our website at www.lrp.cc:
#82505
Power-Wire Set Brushless 2.6mm² (red, black, blue, orange, yellow)
#82506
Power-Wire Set Brushless 3.3mm² (red, black, blue, orange, yellow)
#81907
3.3mm² Powerwire black (1.0m)
#81908
3.3mm² Powerwire blue (1.0m)
#82511
Low Profile cooling fan
#819307
Sensor-Wire „HighFlex“ 70mm
#819310
Sensor-Wire „HighFlex“ 100mm
#819315
Sensor-Wire „HighFlex“ 150mm
#819320
Sensor-Wire „HighFlex“ 200mm
#82520
Radical Motor He Fan
Team advise:
A good starting point for the brake setting on your radio is 80% for all classes. Make sure you do the
radio-setup with all settings on the radio on 100% and then decrease brake strength to 80%!
The crossed-out wheeled bin means that within the European Union the product must be taken
to seperate collection at the product end-of-life. Do not dispose of these products as unsorted
municipal waste.