3. OPERATION
© LRP electronic GmbH 2008
ORDER NO.:
65800
1. WARNING NOTES
LA00104
Dear Customer,
Thank you for your trust in this LRP product. By purchasing the LRP HighPower Soldering Station you have
choosen a high performance station full of new design features, such as:
• 90W High Power
• Adjustable AutoSleep and AutoShutdown function
• Advanced Digital, microprocessor controlled
• Large, blue backlit LCD Display
• Up to 480°C tip temperature
• Lightweight and compact design
• Wide range (100-240V) switching power supply
• Intuitive to use with 3 push buttons
Please read and understand these instructions completely before you use this product! With operating this
product, you accept the LRP warranty terms.
This manual contains important notes for safety, the use and the maintenance of this product. Thus protecting
yourself and avoid damages of the product. This manual shall be kept in a safe place. If another customer is
using this product, this manual shall be passed to him.
Press and button at the same time while switching on the station to enter “Basic Settings”. The LCD shows
the current settings and you can alter them by using the / buttons. Here you can adjust tip size type and
if you want to use an alarm tone or not.
5. BASIC SETTINGS
4. SETTING THE TEMPERATURE
No toy. Not suitable for children under 14 years. Keep the product out of the reach of children.
Pay close attention to the following points, as they can destroy the product and void your warran-
ty. Non-observance of these points can lead to property damage, personal and severe injuries!
• Never leave the product unsupervised while it is switched on, in use or connected with a power
source. If a defect occurs, it could set fire to the product or the surroundings.
• When the power is on, the tip temperature is very high. Mishandling may lead to severe burns or fire.
Never touch the tip or the metal parts nearby while the power is switched on or has been switched
off shortly before.
• Do not replace handle or tips before turning the power off and let everything cool down to room
temperature.
• Never allow this product or other electronic components to come in contact with water, oil or fuels
or other electroconductive liquids, as these could contain minerals, which are harmful for electronic
circuits. If this happens, stop the use of your product immediately and let it dry carefully.
• Never cut off or modify the original plugs and original wires.
• Never open the product and never solder on the PCB or other components.
• Never use this product when the case is open, damaged or missing or when the product is wrapped
in a shrink-fit tube. This will reduce protection, may cause short circuits and damage the product.
• Always remove the battery from your product or disconnect the product from the power source, if
the product is not in use.
• During usage, the product has to be kept on a non-flammable, heat-resistant mat. Furthermore no
flammable or highly inflammable objects may be close to the product.
• In the case of damage, the product must not be used until it has been completely repaired.
• The Powersupply has to be used in a well ventilated room.
• Do not manipulate the input power cords.
• The product is equipped with a 3-wire grounding plug and must be plugged into a 3-terminal groun-
ded socket. Do not use an ungrounded socket.
• Do not rap the soldering iron against the work bench to shake off residual solder, otherwise the iron
will be damaged ny shocks.
• Replace only with genuine parts.
• Do not use the Soldering Station for other applications except soldering.
The manufacturer can not be held responsible for damages, which are a result of non-observance
of the warning notes and security advices.
2. TECHNICAL DATA
Input Voltage Range
100 - 240VAC
Power
90W
Output voltage
48V
Temperature Range
80°C - 480°C
AutoSleep - temperature range
50°C - 250°C
AutoSleep - time range
0 - 250min
AutoShutdown - time range
0 - 250min
Temperature Stability
±2°C (Without air flow and no load)
Tip to Ground Resistance
<2Ω
Tip to Ground Potential
<2mV
Heating Element
Electromagnetic heater
Handle Power Cord Length
1.4m
Length of Handle (Without Cord)
180mm
Outer Dimension
155 x 78 x 120mm
Weight (Without power cord)
1Kg
Above specifications and designs will be changed without notice.
DISPLAY:
IRON HOLDER AND SPONGE
Dampen the small cleaning sponge with water and squeeze it dry. Place it in the groove of the iron holder
base. Add a little water to the iron holder. The small sponge will absorb the water to keep the large sponge
above it wet all times. Dampen the large cleaning sponge and place it on the iron holder base.
CONNECTIONS
CAUTION:
Be sure to turn off the power switch before connecting or disconnecting the soldering station
and iron. Failure to do so may damage the soldering station.
Attach the handle cords connector to the socket at the front of station. Take notice of the correct inser-
ting position!
Place the handle in the MultiFunction Holder.
Insert the input power connector into the power socket.
Switch on the power supply.
Do not turn off the power supply while setting the temperature since the new value would not be stored.
TEMPERATURE UP:
Press button, the “Set Temp” will rise 1°C and the LCD will show the setting temperature. If you keep the
button pressed ~1sec, the setting temperature will rise quickly. Keep the button pressed until your desired
temperature has been reached.
TEMPERATURE DOWN:
Press button, the “Set Temp” will drop 1°C and the LCD will show the setting temperature. If you keep the
button pressed ~1sec, the setting temperature will drop rapidly. Keep the button pressed until your desired
temperature has been reached.
Working mode
Temperature range
Tip type
Remark
0
80°C - 480°C
Normal Tip
is a alarming mark
1
80°C - 480°C
Big Tip
0
80°C - 480°C
Normal Tip
1
80°C - 480°C
Big Tip
6. ADVANCED SETTINGS
From above “Basic Settings”, you can continue to “Advanced Settings” by pressing button and scroll through
to the different “Advanced Settings” by pressing further. All values can be adjusted by pressing the /
buttons.
A) AUTOSLEEP – TIME SETTING:
The stations AutoSleep function will come effective if you don’t use the station
for the set AutoSleep time. It will go into sleep state and lower the tip tempera-
ture in order to extend tip life and safe energy.
The LCD indicates:
use / buttons to adjust the AutoSleep time (range 0-250min).
you disable AutoSleep function by selecting 000min.
B) AUTOSHUTDOWN – TIME SETTING:
As another safety feature, the station has a built in AutoShutdown which turns
power off completely if the station is not used for this period of time. This will
further extend tip life and avoids a running station for several hours for no use.
The LCD indicates:
use / buttons to adjust the AutoShutdown time (range 0-250min).
you disable AutoShutdown function by selecting 000min.
the choosen AutoShutdown time should be longer than the choosen Auto-
Sleep time, otherwise the soldering station will be turned off immediately
after it comes into sleep state.
C) AUTOSLEEP – TEMPERATURE SETTING:
Here you select to which temperature the station will regulate, once it is in Au-
toSleep state.
The LCD indicates:
use / buttons to adjust the AutoSleep temperature (range 50-250°C).
IMPORTANT NOTES ABOUT “ADVANCED SETTINGS”:
1. The temperature will always regulate to lowest setting, no matter if working- or AutoSleep-Temperature
are set lower. As an example:
if AutoSleep is 200°C and the work temperature is 350°C, the station will regulate to 200°C in sleep
state.
if AutoSleep is 200°C and the work temperature is 150°C, the station will regulate to 150°C in sleep
state.
2. If soldering station is in AutoSleep state, there are three ways to resume soldering:
a) Take up the handle (there is a magnet positioned inside the holder for recognition).
b) Turn the power switch off and then turn on.
c) Press button
3. If soldering station is in AutoShutdown state, you need to turn switch off (leave for 3sec) and on again to
resume soldering!
4. The handle must be placed in the Multi Function holder to make use of AutoSleep and AutoShutdown
function!
SleepTime
OffTime
Sleep
SetTemp
USER MANUAL
LRP electronic GmbH
Wilhelm-Enssle-Str. 132-134
73630 Remshalden
Germany
www.LRP.cc
heating indication
setting temperature
alarming mark
real temperature
Basic Settings
SleepTime
OffTime
Sleep
SetTemp
Setting temperature
Press
Press
Press
Press
