manualshive.com logo in svg

Lovibond Maxi Direct, Instruction Manual, Page: 6 / 268

Share
Download
Lovibond Maxi Direct Instruction Manual Download Page 6

4

MaxiDirect_2c   03/2010

  Phosphate, ortho (powder pack) ............................................................................... 150
  Phosphate, ortho (tube test) ...................................................................................... 152
  Phosphate 1, ortho C ................................................................................................ 154
  Phosphate 2, ortho C ................................................................................................ 156
  Phosphate, hydrolyzable (tube test) ........................................................................... 158
  Phosphate, total (tube test) ....................................................................................... 160
Phosphonates ............................................................................................................... 162
pH value LR with tablet ................................................................................................. 166
pH value with tablet ...................................................................................................... 168
pH value with liquid reagent ......................................................................................... 170
pH value HR with tablet ................................................................................................ 172
Potassium ..................................................................................................................... 174
Silica ............................................................................................................................. 176
Silica LR PP .................................................................................................................... 178
Silica HR PP ................................................................................................................... 180
Sodium hypochlorite ..................................................................................................... 182
Sulfate with tablet ........................................................................................................ 184
Sulfate (powder pack) ................................................................................................... 186
Sulfide .......................................................................................................................... 188
Sulfite ........................................................................................................................... 190
Suspended Solids .......................................................................................................... 192
Turbidity ....................................................................................................................... 194
Urea ............................................................................................................................. 196
Zinc .............................................................................................................................. 198

1.2 

Important notes

 ......................................................................................... 200

1.2.1 

Correct use of reagents ................................................................................ 200

1.2.2 

Cleaning of vials and accessories for analysis ................................................ 201

1.2.3 

Guidelines for photometric measurements ................................................... 201

1.2.4 

Sample dilution techniques ........................................................................... 203

1.2.5 

Correcting for volume additions ................................................................... 203

Part 2  Instrument Manual

 ....................................................................... 205

2.1 

Operation

 ................................................................................................... 206

2.1.2 

Saving data – Important Notes ..................................................................... 206

2.1.3 

Replacement of batteries .............................................................................. 206

2.1.4  

Instrument (explosion drawing) .................................................................... 207

Summary of Contents for Maxi Direct













































































































































































































































































Reviews:

No comments