manualshive.com logo in svg

Lovibond Maxi Direct, Instruction Manual, Page: 265 / 268

Share
Download
Lovibond Maxi Direct Instruction Manual Download Page 265

263

MaxiDirect_2c   03/2010

3.6.2 General

Finding                

Possible Causes

Elimination 

Test result deviates from 
the expected.

Chemical species not as 
required.

Press arrow keys to select the 
required chemical species.

No differentiation:  
e.g. for the Chlorine test  
there is no selection 
between differentiated, 
free or total. 

Profi-Mode is switched on.

Switch Profi-Mode off with 
Mode 50.

The pre-programmed 
countdown is not 
displayed.

Countdown is not activated 
and/or the Profi-Mode is 
activated.

Switch the countdown on 
with Mode 13 and/or switch 
the Profi-Mode off with 
Mode 50.

It seems that a method  
is not available.

Method is not activated in 
the user method list.

Activate the required method 
in the user method list with 
Mode 60.

Summary of Contents for Maxi Direct













































































































































































































































































Reviews:

No comments