manualshive.com logo in svg

Lovibond Maxi Direct, Instruction Manual, Page: 232 / 268

Share
Download
Lovibond Maxi Direct Instruction Manual Download Page 232

230

MaxiDirect_2c   03/2010

Recall results of one selected method

Press [MODE], [Shift] + [3][3] keys.

Confirm with [ ] key.

The display shows:

Select the required method from the displayed list or enter 
the method number directly.

Confirm with [ ] key.

In case of differentiated methods select the required kind 
of determination and confirm with [ ] key.

The display shows:

•  Press 

[ ]  key  and  all  stored  results  of  the  selected 

 

method are displayed.

•  Press [F3] key to print the displayed result.

•  Press [F2] key to print all selected results.

•  End with [ESC].

 <Storage>
 >>

20

 Acid demand

     30 Alkalinity-tot
     40 Aluminium T

 <Storage>
 method 
 30 Alkalinity-tot
 Start:    cancel: ESC 
 print: F3 
 print all: F2

Mode

3

3

Summary of Contents for Maxi Direct













































































































































































































































































Reviews:

No comments