manualshive.com logo in svg

Lovibond Maxi Direct, Instruction Manual, Page: 214 / 268

Share
Download
Lovibond Maxi Direct Instruction Manual Download Page 214

212

MaxiDirect_2c   03/2010

2.3.2.2  Chemical Species Information

Pressing the [F2] key the display shows a list with available chemical species and corresponding 
ranges. Changing chemical species see chapter 2.3.7 page 214.

Line 1: Method number, Method name
Line 2: Range with chemical species 1
Line 3: Range with chemical species 2
Line 4: Range with chemical species 3

 

2.3.3 Differentiation

Differentiation is possible in some methods (e.g. Chlorine). 
The photometer then requires the type of determination.

Press arrow key [ ] or [ ] to select the required determi-
nation.

Confirm with [ ] key.

2.3.4 Performing Zero

The display shows:

Prepare a clean vial as described in “Method“ and place the 
vial in the sample chamber making sure that the   marks 
are aligned.

Press [ZERO] key.

The display shows:

 prepare Zero
 press ZERO

 Zero accepted
 prepare Test
 press TEST

 Chlorine
      >>   diff
   

free

   

total 

Chemical Species 

Information 
Information

Methods

Information

Method List

Method

F1

F2

F1

F1

F2

F2

  320 Phosphate LR T
  0.05-4 mg/l PO

4

  0.02-1.3 mg/l P
  0.04-3 mg/l P

2

O

5

Zero

Summary of Contents for Maxi Direct













































































































































































































































































Reviews:

No comments