manualshive.com logo in svg

Lovibond Maxi Direct, Instruction Manual, Page: 197 / 268

Share
Download
Lovibond Maxi Direct Instruction Manual Download Page 197

195

MaxiDirect_2c   03/2010

1.1 Methods

Note:

1. This test uses an attenuated radiation method for the reading of FAU (Formazin  
  Attenuation Units). The results can not be used for USEPA reporting purposes, but may  
  be used for routine measurements. The attenuated radiation method is different from  
  the Nephelometric method.
2. The estimated detection limit is 20 FAU.
3. Collect water samples in clean plastic or glass bottles and analyse the water sample as  
  soon as possible. It is possible to store the sample at 4°C for 48 hours. Before  
  measurement warm up the sample to the temperature at collection time. Temperature  
  differences between measurement and sample collection can effect the turbidity of the  
  sample.
4. Colour interferes if light is absorbed at 530 nm. For strong coloured water samples a  
  filtrated portion of the sample can be used for zeroing instead of the deionised water.
5. Air bubbles interfere and can be removed using an ultrasonic bath.

Summary of Contents for Maxi Direct













































































































































































































































































Reviews:

No comments