manualshive.com logo in svg

Lovibond Maxi Direct, Instruction Manual, Page: 185 / 268

Share
Download
Lovibond Maxi Direct Instruction Manual Download Page 185

183

MaxiDirect_2c   03/2010

1.1 Methods 

8.  Place the vial in the sample chamber making sure that 

the   marks are aligned.

9.  Press 

TEST

 key.

 

The result is shown in the display in % w/w as availa-
ble chlorine present in the original sample of Sodium 
hypochlorite.

Notes:

1. Please pay attention when handling sodium hypochlorite. The material has a very strong  
  alkalinity and can cause corrosion. Contact with eyes, skin and clothes etc.has to be  
  avoided. Refer to the detailed information the producer supplied with the product.
2. The tablets must be added in the correct sequence.
3. This method provides a fast and simple test. The test can be performed on site but the  
  result will not be as precise as a laboratory method.
4. By strictly following the test procedure, an accuracy of +/- 1 weight % can be achieved.

 Zero accepted
 prepare Test
 press TEST

Summary of Contents for Maxi Direct













































































































































































































































































Reviews:

No comments