manualshive.com logo in svg

Lovibond Maxi Direct, Instruction Manual, Page: 176 / 268

Share
Download
Lovibond Maxi Direct Instruction Manual Download Page 176

174

MaxiDirect_2c   03/2010

1.1 Methods

Potassium   

with Tablet

0.7 – 12 mg/l K

1.  Fill a clean vial (24 mm Ø) with 

10 ml of the water 

sample

, close tightly with the cap.

2.  Place the vial in the sample chamber making sure that 

the   marks are aligned.

3.  Press 

ZERO

 key.

4.  Remove the vial from the sample chamber.

5.  Add 

one Potassium T tablet

 straight from the foil to 

the water sample and crush the tablet using a clean 
stirring rod.

6.  Close the vial tightly with the cap and swirl several times 

until the tablet is dissolved.

7.  Place the vial in the sample chamber making sure that 

the   marks are aligned.

8.  Press 

TEST

 key.

 

The result is shown in the display in mg/l Potassium.

 prepare Zero
 press ZERO

 Zero accepted
 prepare Test
 press TEST

4

0

3

Summary of Contents for Maxi Direct













































































































































































































































































Reviews:

No comments