background image

GENERAL INFORMATION

Translation of the original instructions

9

2.2

User information, RAEE Directive on waste electrical and
electronic equipment

With regard to the regulatory framework of reference of the European Community, we remind the user of the
following:
 

·

Used AAE (Electrical and Electronic Equipment) products must be collected separately

·

The user can carry out this collection in the RAEE collection systems and return the equipment to the

distributor when purchasing a new one

·

Plus being RoHS compatible, (in accordance with Directive 2011/65/EU on the restriction of the use of

certain hazardous substances in electrical and electronic equipment) the potential effects on the
environment and human health may be due to the misuse of the same equipment or parts of it

·

The symbol

next to the rating plate indicates the obligation of separate collection

·

The penalties provided for in the event of improper disposal of RAEE (Waste Electrical and Electronic

Equipment) are those provided for by the national transpositions of European Directives 2012/19/EU

2.3

Technical data table

Electrical technical data table F S70ETD

MODEL

DIMENSIONS

POWER SUPPLY

MAXIMUM

POWER (kW)

MAXIMUM INPUT

(A)

Silicon POWER

SUPPLY CABLE

F18-74ETD

40x70,5x90h

400V~3N 50/60Hz

15,95

22,95

5 x 2,5 mm²

F18-74ETDP

40x70,5x90h

400V~3N 50/60Hz

16,2

24,13

5 x 2,5 mm²

F18-74ETDPS

40x70,5x90h

400V~3N 50/60Hz

16,55

25,65

5 x 4 mm²

F2/18-78ETD

80x70,5x90h

400V~3N 50/60Hz

31,9

45,9

5 x 10 mm²

F2/18-78ETDP

80x70,5x90h

400V~3N 50/60Hz

32,4

48,26

5 x 10 mm²

F2/18-78ETDPS

80x70,5x90h

400V~3N 50/60Hz

33,1

51,3

5 x 10 mm²

 

Summary of Contents for F18-74ETD
















Reviews: