manualshive.com logo in svg

LORD 6254-4220, User Manual

Share
Download
LORD 6254-4220 User Manual Download Page 28

3DM

®

-GX5-15

User Manual

4.3.3

Sensor Frame

The sensor frame is indicated on the top of the device and is oriented such that the x-axis vector is

parallel with the long side of the sensor and points toward the sensor connector, the y-axis is 90° to

the right of the x-axis, and the z-axis goes through the bottom of the sensor (outward). These axes

were selected so that when the connector on the device is pointed north and the device is upright

and level, the sensor frame will match the NED frame exactly, giving zero rotation.

The 3DM- GX5- 15 reports acceleration, angular rate, delta- theta, delta- velocity, inertial sensor

biases and corrections in this frame. When no sensor-to-platform frame transformation has been

provided (

see Platform Frame on page 1

).

The orientation of the sensor frame with respect to the local NED frame can be viewed in the

MIP Monitor software at: View > 3D Attitude menu. This window displays the orientation of the

sensor in relationship to north and shows measurement origination for acceleration and angular

rate. The view can be rotated for clicking, holding, and dragging the image.

Refer to the 3DM-GX5-15 dimensional diagram for the location of the measurement origin (

see

Sensor Dimensions and Origin on page 54

).

Figure 19 -Sensor Frame

28

Summary of Contents for 6254-4220


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands