manualshive.com logo in svg

LORD 6254-4220, User Manual

Share
Download
LORD 6254-4220 User Manual Download Page 15

3DM

®

-GX5-15

User Manual

3.5

Sensor Settings

Device settings are stored in the sensor memory. Only the configuration options available for the

sensor being used are displayed in the menus.

To enter the settings menu, either right-click on the sensor name highlighted in the main window, and

then select Device Settings, or select Settings > Device from the main menu.

a. Main menu tabs: The main tabs divide the settings into functional groups for the available

measurements. For the 3DM-GX5-15 these include calculated measurements (Estimation Fil-

ter) and direct inertial sensor measurements (IMU/AHRS).

b. Message Format (first sub-menu tab): Under each main menu tab there are additional sub-

menu tabs, including the Message Format tab, which allows the user to select the meas-

urement type to be displayed and recorded (b1) and the data rate in samples/second(b2).

c. Measurement parameters: Available sub-menu tabs depend on the selected main menu tab.

They include the configurable settings for each measurement.

d. Scrolling: used to navigate to additional sub-menus

e. Help button: Enable the context-sensitive help menu for more information (

see Interactive

Help Menu on page 13

).

Figure 9 -Device Settings Menu

15

Summary of Contents for 6254-4220


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands