LORD 6254-4220 User Manual Download Page 11

Page: 11 / 65

3DM

-GX5-15

User Manual

3.1

Software Installation

NOTE

The MIP Monitor Software Suite includes hardware drivers required for 3DM-GX5-15 sensor

operation. Sensors will not be recognized without these drivers installed.

To Install the MIP Monitor software on the host computer, complete the following steps:

1. Launch the MIP Monitor software installation menu at:

https://www.microstrain.com/software

2. Download and open the MIP Monitor .zip file.

3. Run the setup.exe file, and follow the on-screen prompts to completion.

4. Download and open the Inertial Drivers zip folder to install the hardware drivers required

for operating the sensor.

5. Run the .msi file, and follow the on-screen prompts to completion.

6. Run the setup.exe file, and follow the on-screen prompts to completion. If prompted,

reboot the computer when complete.

Figure 4 -Software Installation Menu

Summary of Contents for 6254-4220


































































Search results

Summary of Contents for 6254-4220

Reviews:

Brands by name

Popular brands

LORD 6254-4220, User Manual

Search results

Summary of Contents for 6254-4220

Reviews:

Brands by name

Popular brands