LORD 6254-4220 User Manual Download Page 10

Page: 10 / 65

3DM

-GX5-15

User Manual

Basic Setup and Operations

To acquire sensor measurements and computed outputs, the 3DM-GX5-15 uses a host computer,an

RS232 or USB communications port, and applicable software. The LORD Sensing MIP Monitor software

is provided with the system and includes all functions needed for sensor configuration and data

acquisition. Users may also utilize the LORD Sensing MIP Data Communications Protocol (DCP) to write

custom software applications with expanded or specific feature sets needed for the application.

MIP Monitor includes a message building tool that can be used to streamline this process. For more

information,

see OEM System Integration on page 37

In this section, hardware and software setup is described, including an overview of the MIP Monitor

software menus required to configure a sensor and begin data acquisition. This is not a complete

demonstration of all system or software features and capabilities.

Figure 3 -Viewing Sensor Data with MIP Monitor

Summary of Contents for 6254-4220


































































Search results

Summary of Contents for 6254-4220

Reviews:

Brands by name

Popular brands

LORD 6254-4220, User Manual

Search results

Summary of Contents for 6254-4220

Reviews:

Brands by name

Popular brands