background image

page 48

Monitoring bus voltage

Right from switching on the machine, the bus voltage is monitored directly by the DSP of the DRV.

The actual value of the bus voltage is send from the DSP of the DRV to the MAPRO.

As soon as the voltage gets too high, the machine stops with 

E02

 “Overvoltage”. In this case the power-up relays 

on the DRV are switched off, so that the power-up resistors are active again, lowering the input voltage.

If the minimum value of 390V DC is not reached during startup (switching on), the machine stops with 

E22-03

“Undervoltage Startup”.

Schematic

RE1

RE2

X17

1

2

3

4

-Uz

+Uz1

+Uz2

-Uz2

TM2

TM1

DSP

X2-3*
X2-4*

FPGA

X7-4
X7-5

MAPRO

DRV

RS485

RS485

*(at the DRV05 the connector designation X19 was later renamed into X2)

In general the values of both bus voltages at the power modules TM1 and TM2 are equal (symmetrical). If there  

should be a difference >60V, the machine stops with 

E33-01

 Unsymmetrical bus voltage.

If a difference >60V is detected during startup, the machine stops with 

E33-02

 Unsymmetrical bus voltage Startup.

As soon as the difference gets below 60V, the error code is reset.

Code Cause

E02-02

During startup the maximum limit of 700V DC was exceeded.

E02-04

The maximum limit of 750V DC (or 400V DC at the modules) was exceeded during operation.

E02-05

The FPGA measured a too high bus voltage (>400V DC) at the modules.

E22-03 During startup the minimum limit of 390V DC was not reached.
E33-01

The difference between the bus voltages of module 1 and 2 is greater 60V.

E33-02

The difference between the bus voltages of module 1 and 2 is greater 60V at startup.

Summary of Contents for MicorMIG 300





































































Reviews: