Loongson 3A3000 User Manual Download

Page: 69 / 128

4/29/2020

Loongson 3A3000 / 3B3000 Processor User Manual

Offset:

0xc4

Reset value:

0x00000000

name:

Dataport

Table 10- 43 Datap Yaot Register Definition

Bit field

Bit field name

Bit width reset value Visit description

31: 0

Dataport

0x0

R / W When the previous register Index is 0x10, this register is read and written

The result is the 0xa8 register, otherwise 0xac

Offset:

0xc8

Reset value:

0xF8000000

name:

IntrInfo [31: 0]

Table 10-44 Definition of Int and Inf Yao Register (1)

Bit field

Bit field name

Bit width reset value Visit description

31:24

IntrInfo [31:24]

0xF8

Keep

23: 2

IntrInfo [23: 2]

twenty two

0x0

R / W IntrInfo [23: 2], when the PIC interrupt is issued, the value of IntrInfo

Used to represent interrupt vector

1: 0

Reserved

0x0

Keep

Offset:

0xcc

Reset value:

0x00000000

name:

IntrInfo [63:32]

Table 10-45 Int Yao Inf Yao register definition (2)

Page 86

Godson 3A3000 / 3B3000 Processor User Manual • Volume 1

Bit field

Bit field name

Bit width reset value Visit description

31: 0

IntrInfo [63:32]

0x0

Keep

10.5.11

POST address window configuration register

For the address window hit formula, see section 10.5.7.

The address in this window is the address received on the AXI bus. All write accesses that fall in this window will be immediately in AXI B

The channel returns and is sent to the HT bus in the format of the POST WRITE command. Instead of writing requests in this window, NONPOST

WRITE is sent to the HT bus, and waits for the HT bus to respond before returning to the AXI bus.

Offset:

0xd0

Reset value:

0x00000000

name:

HT bus POST address window 0 enable (internal access)

Table 10-46 HT Bus POST Address Window 0 Enable (Internal Access)

Bit field

Bit field name

Bit width reset value Visit description

ht_post0_en

0x0

R / W HT bus POST address window 0, enable signal

ht_depart0_en

0x0

R / W HT access unpacking enable (corresponding to external CPU core

uncache ACC operation window)

29:23

Reserved

0x0

Keep

15: 0

ht_post0_trans

[39:24]

0x0

R / W HT bus POST address window 0, the translated address [39:24]

Summary of Contents for 3A3000

































































































































Search results

Summary of Contents for 3A3000

Reviews:

Related manuals for 3A3000

Brands by name

Popular brands

Loongson 3A3000, User Manual

Search results

Summary of Contents for 3A3000

Reviews:

Related manuals for 3A3000

Brands by name

Popular brands