background image

8 - Control with the Lode Ergometry Manager (LEM)

1. If your device has an RS232 or USB port, connect it directly to the PC LEM is installed on. If your
device has a RJ45 connector plug it with an UTP cable to the special interface connector that was
delivered with your device and to a USB port in your PC.
2. Start Lode Ergometry Manager on your PC
3. If your device has a control unit, select “Terminal”- mode to allow external command. If your device
does not have a control unit the terminal mode is automatically selected. (See for detailed instructions
the user manual of LEM).

9 - Control with an External Device

If your device is fitted with a communication card you can connect to many external devices.

1. Connect the device with the supplied cable to the external device. You can control the device with
e.g. an exercise ECG device or Metabolic Card.
2. Download the interfacing instructions from the internet at www.lode.nl after you have registered
your device.
3. If your device has a control unit, select “Terminal”- mode to allow external commands. When the
device does not have a control unit the terminal mode is automatically selected. (See for detailed
instructions the user manual of your external device).

10 - Maintenance

Maintenance should be carried out on a regular and planned basis. We recommend to check the unit
annually. This may be done by your local dealer. It is also recommended that a record of the service
history is kept for all activities relating to service and maintenance. 

Maintenance and all repairs should only be carried out by an authorized agency. The manufacturer will
not be held responsible for the results of maintenance or repairs by unauthorized persons. 
The check up and/or technical maintenance must be carried out conform the procedure described in
the service manual of the unit.
Opening of the equipment by unauthorized agencies is not allowed and will terminate any claim to
warranty. 

Lode will make available on request circuit diagrams, component part lists, descriptions, calibration
instructions, or other information that will assist authorized service personnel to repair those parts of
the ergometer that are designated by Lode as repairable by authorized service personnel.

15/24

M960900 / VERSION: 1.0 - 2014-09-24

Summary of Contents for 960900

























Reviews: