background image

*829767-00*

829767-00

The LP150/LP250 is a power-limited power supply and battery charger that will convert 120 VAC / 60Hz input into field-selectable 12 VDC 

or 24 VDC Class 2 rated outputs (one continuous, one switchable). It is intended for use in applications with UL listing requirements (see 

specifications below for specific listings).

This instruction covers: 

PS150/250

Power Supply

Enclosure

with hinged cover

+ Board

Battery Wire Kit

RDB4 board included

with LP250RDB4 only

and is covered in

separate instruction

LP150 

  PS c board (1.5A), battery wire kit, keylock

LP250 

  PS c board (2.5A), battery wire kit, keylock

LP250RDB4    PS c board (2.5A), battery wire kit, keylock,  
 

  RDB4 board * 

 

LP150B 

PS board only (1.5A), 4 mounting screws

LP250B 

PS board only (2.5A), 4 mounting screws

Keylock

PS board

RDB4

*

PS150/250 Specifications:

 

Input

LP150: 120 VAC, 1A,  60Hz            LP250: 120 VAC, 1.2A,  60Hz

 

      

Output

LP150: 12 VDC (13.2V nominal) or 24 VDC (26.4V nominal), 1.5A, Class 2 rated

 

LP250 (LP250RDB4): 12 VDC (13.2V nominal) or 24 VDC (26.4V nominal), 2.5A, Class 2 rated

Output Protection

DC OUT and CONTROL OUT are protected from overload or shorts via self-resetting electronic protection circuit

Battery Protection

PTC

Environment

32°-120° F (0°- 49° C), up to 85% relative humidity, indoor use only, protected area

Compliance

UL294, UL603, Access control performance levels: Attack: I, Line security: I, Endurance: IV, Standby power: III 

(LP150) and II (LP250/LP250RDB4), CSA22.2 NO. 205, CSFM, FCC

Battery Backup

Requires 12V, 7AH max. rechargeable sealed lead acid battery: (1) for 12V, (2) for 24V output. 

 

Battery maximum dimensions: 3-3/4” H x 6” W x 3” D

 

See typical backup times in Section 2

 

See Section 8 for maintenance of battery

Control Input / Output

Input: Normally closed, requires dry contact rated at 24 VDC, 10mA

 

Output: Powered NC/NO contacts rated at 24 VDC, 2.5A

AC Status

Indicator: Green LED 

 

Relay contacts: NO/NC contacts rated at 24 VDC, 1A

DC Output Status

Indicator: Red LED 

Battery Status

Indicator: Red LED

 

Relay contacts: NO/NC contacts rated at 24 VDC, 1A

Enclosure

13” H x 12-5/8” W x 3-1/4” D (8 knockouts, 1/2” or 3/4”) 

Power Supply

LP150, LP250

 

LP150B, LP250B

 

LP250RDB4

Installation Instructions

Summary of Contents for LP150

















Reviews: