background image

Dear Specifier/Project Manager,

At Lochinvar, we have long recognized the importance of innovation to any
product or service. Those who enter into business must also accept the challenge
of meeting constantly changing needs.

The designer’s guide you are now holding has been designed to make it more
convenient for you to select the perfect Lochinvar water heater for your projects
and provide correct specifications for your teams.

All information has been organized and presented in a succinct, easy-to-use
manner, so you can use and share information confidently and with minimal
effort.

However, it is important to remember that this guide is not intended to replace our
installation manual. Installers should still refer to our installation manual for
specific installation instructions. 

We hope our manual will make your work easier and more productive.
As always, we greatly appreciate your input on additional improvements for the
future. 

Thanks once again for specifying the Lochinvar family of quality standard
and custom-built water heaters and boilers. 

Sincerely,

Lochinvar Corporation

L o c h i n v a r   C o r p o r a t i o n   •   6 1 5 - 8 8 9 - 8 9 0 0   •   F a x :   6 1 5 - 5 4 7 - 1 0 0 0

Summary of Contents for Power-Fin PF 1500

































Reviews: