background image

4.4   exclusions

The warranty set out in articles 1 and 2 

will not apply in the event of:

a. damage to the water heater caused by 

an external factor;

b. misuse, neglect (including frost 

damage), modification and  incorrect 

and/or unauthorized use of the water 

heater;

c. contaminants or other substances 

having been allowed to enter the tank;

d. any attempts at repair to a defective 

water heater other than by an appro

-

ved service engineer.

4.5   scope of the warranty

The obligations of Lochinvar Ltd 

pursuant to the specified warranty 

are limited to free delivery from 

the warehouse of the replacement 

assemblies, parts or water heater, 

respectively. Labor, installation and 

any other costs associated with the 

replacement will not be accepted by 

Lochinvar Ltd.

4.6   Claims

A claim on grounds of the specified 

warranty must be submitted to the 

dealer from whom the water heater was 

purchased, or to another authorized 

dealer of Lochinvar Ltd. Inspection of 

the water heater as referred to in articles 

1 and 2 shall take place in one of the 

laboratories of Lochinvar Ltd.

4.7   obligations of lochinvar ltd

Lochinvar Ltd grants no other warranty 

or guarantee over its water heaters 

nor the (assemblies or parts of) water 

heaters supplied for replacement, other 

than the warranty expressly set out in 

these conditions.

Under the terms of the supplied 

warranty, Lochinvar Ltd is not liable for 

damage to persons or property caused 

by (assemblies or parts, or the glass-

lined steel tank of) a (replacement) water 

heater that it has supplied.

26

Summary of Contents for Knight LG30GCE





























Reviews: