⅐ ⁆⁄⁁⁇‴‾‷⁅›⁁⁁⁆※⁀‹
If a problem occurs, check the following.
㻌
If the problem persists after checking the items in the table
below, contact your nearest ‘‘LOBSTER’’ dealer or contact Lobtex.
ᵧᶌᴾᶋᵿᶉᶇᶌᶅᴾᵿᶌᶗᴾᶇᶌᶏᶓᶇᶐᶇᶃᶑᴾᵿᶀᶍᶓᶒᴾᶒᶆᶇᶑᴾᶎᶐᶍᶂᶓᶁᶒᴾᶍᶐᴾᶐᶃᶏᶓᶃᶑᶒᶑᴾᶄᶍᶐᴾᶐᶃᶎᵿᶇᶐᴾᶕᶍᶐᶉᵊᴾᶄᶇᶐᶑᶒᴾᶁᶆᶃᶁᶉᴾᶒᶆᶃᴾᶒᶐᶍᶓᶀᶊᶃᶑᶆᶍᶍᶒᶇᶌᶅᴾ
ᶀᶃᶊᶍᶕᴾ ᵿᶌᶂᴾ ᶒᶆᶃᶌᴾ ᶋᵿᶉᶃᴾ ᵿᴾ ᶌᶍᶒᶃᴾ ᶍᶄᴾ ᶒᶆᶃᴾ ᶋᶍᶂᶃᶊᴾ ᶌᶓᶋᶀᶃᶐᵊᴾ ᶒᶆᶃᴾ ᶓᶑᵿᶅᶃᴾ ᶁᶍᶌᶂᶇᶒᶇᶍᶌᶑᴾ ᵿᶌᶂᴾ ᶒᶆᶃᴾ ᶒᶐᶍᶓᶀᶊᶃᴾ ᶑᶗᶋᶎᶒᶍᶋᶑᴾ ᶇᶌᴾ
ᵿᶑᴾ ᶋᶓᶁᶆᴾ ᶂᶃᶒᵿᶇᶊᴾ ᵿᶑᴾ ᶎᶍᶑᶑᶇᶀᶊᶃᵌᴾ ᵧᶄᴾ ᶗᶍᶓᴾ ᶁᵿᶌᴾ ᶎᶐᶍᶔᶇᶂᶃᴾ ᶒᶆᶇᶑᴾ ᶉᶇᶌᶂᴾ ᶍᶄᴾ ᶇᶌᶄᶍᶐᶋᵿᶒᶇᶍᶌᵊᴾ ᶇᶒᴾ ᶋᵿᶗᴾ ᶐᶃᶂᶓᶁᶃᴾ ᶒᶆᶃᴾ ᵿᶋᶍᶓᶌᶒᴾ ᶍᶄᴾ
ᶒᶇᶋᶃᴾᶐᶃᶏᶓᶇᶐᶃᶂᴾᶄᶍᶐᴾᶂᶃᶊᶇᶔᶃᶐᶗᴾᶍᶐᴾᶐᶃᶎᵿᶇᶐᶑᴾᶒᶍᴾᶀᶃᴾᶁᶍᶋᶎᶊᶃᶒᶃᶂᵌ
6TQWDNG
ᵡᵿᶓᶑᶃ
%QWPVGTOGCUWTG
ᵲᶆᶃᴾᶐᶇᶔᶃᶒᴾᶂᶍᶃᶑᴾᶌᶍᶒᴾᶅᶍᴾ
ᶇᶌᵊᴾᶍᶐᴾᶒᶆᶃᴾᶁᶓᶒᴾᶋᵿᶌᶂᶐᶃᶊᴾ
ᶂ ᶍ ᶃ ᶑ ᴾ ᶌ ᶍ ᶒ ᴾ ᶁ ᶍ ᶋ ᶃ ᴾ ᶍ ᶓ ᶒᴾ
ᵿᶄᶒᶃᶐᴾᶐᶇᶔᶃᶒᶇᶌᶅᵌ
1 Wrong type of Nosepiece or Guide
Pipe.
Replace with the correct part which
matches the rivet size. (
Refer to page
12 and 13 )
2 Nosepiece or frame head is loose. Use a spanner or similar to tighten
securely. ( Refer to page 12 and 13 )
3 Jaw Case is incorrectly assembled. Check the procedure to assemble Jaw
Case. ( Refer to page 12 )
4 Contact surfaces between the jaws
and the jaw case head are not
㻌
smooth.
Clean the jaws and inside the jaw case
head, and apply “LOBSTER” brand jaw
lube
to the backs of the jaws.
䚷
(Refer to
page 12 )
5 Inside of the Frame Head is dirty
so that the Jaws cannot open
properly.
Clean inside the Frame Head and the
Jaws. ( Refer to page 12 )
6 Tip of the Nosepiece got broken
and Jaw does not open properly.
Replace the Nosepiece. ( Refer to page
13 )
7 Inside of the cylinder is dirty so
that the air piston cannot return
㻌
to
its proper position.
Clean inside the cylinder, and apply
grease inside the cylinder and to the
o-ring. ( Refer to page 15 )
8 O i l f i l l i n g w a s n o t p e r f o r m e d
correctly, so that there is excess
hydraulic oil inside the tool.
Take off Frame Head and loosen the
Bleed Plug and take out the extra oil.
( Refer to page 15 )
9 The Jaw Pusher or the guide pipe
is clogged with mandrels.
Take out the mandrel inside the Jaw
Case or Guide Pipe.
㻔
Refer to page 12
㻕
ᵲᶆᶃᴾ ᶒᶐᶇᶅᶅᶃᶐᴾ ᶂᶍᶃᶑᴾ ᶌᶍᶒᴾ
ᶕ ᶍ ᶐ ᶉ ᴾ ᶍ ᶐ ᴾ ᶌ ᶓ ᶋ ᶀ ᶃ ᶐ ᴾ ᶍ ᶄᴾ
ᶎ ᶓ ᶊ ᶊ ᶇ ᶌ ᶅ ᴾ ᶒ ᶆ ᶃ ᴾ ᶒ ᶐ ᶇ ᶅ ᶅ ᶃ ᶐᴾ
ᶆᵿᶑᴾᶇᶌᶁᶐᶃᵿᶑᶃᶂᵌ
1 The rivet length is not correct for
the workpiece thickness.
Use rivets which match the workpiece
thickness.
2 Compressor air pressure is
incorrect.
Check the air pressure.
3 Jaw Case is incorrectly assembled.
( Setting position is incorrect. )
Check the procedure to assemble Jaw
Case. ( Refer to page 12 and 13)
4 Jaws are worn.
Replace the jaws. ( Refer to page 12 )
5
Insuf• cient hydraulic oil, causing a
shorter stroke.
Add hydraulic oil.(After adding the
hydraulic oil, loosen the bleed plug and
let excessive hydraulic oil out.) ( Refer
to page 15 )
䚷
6 Not correct rivet or Nosepiece size
are used.
Check the rivet size and change the
parts which are suitable for rivet size.
( Refer to page 12 and 13 )
7 Contact surfaces between the jaws
and the jaw case head are not
㻌
smooth.
Clean the jaws and inside the jaw case
head, and apply “LOBSTER” brand jaw
lube
to the backs of the jaws.
䚷
(Refer to
page 12 )
䠍䠔
ᒍᛖᾔ
ᾝ
ᾖ
ᾛᾘ
ᾢ
ᾗ
