manualshive.com logo in svg

LK Minishunt M60n, Assembly Instructions Manual, Page: 1 / 10

Share
Download
LK Minishunt M60n Assembly Instructions Manual Download Page 1

1 (10)

Table of contents

Design

1

Supplied with product

1

Accessories

1

LK Minishunt M60n, Overview

2

Function and requirements

3

Assembly

3

Installation cabinets 

5

Start up

5

Circulationspump

7

Troubleshooting

9

Technical data

9

Flow chart

9

Dimensions drawing

10

Design

LK Minishunt M60n is a shunt group intended for use 

when smaller underfloor heating areas are to be con-

nected to an existing heating system. LK Minishunt 

M60n adapts the heating system temperature to the 

lower temperature necessary for the underfloor heat-

ing system. Its capacity can normally be set at a heat-

ing need of 50 W/m² to a maximum 60 m² underfloor 

heating area. Capacity is however dependent on pri-
mary temperature, pressure, laying method etc.

• For underfloor heating areas up to 60 m

2

.

• Compact design.
• Energy efficient circulation pump.
• Thermostat-controlled maximum limit of supply 

temperature.

• Switchable between single or twin pipe systems.
• VF valve.
• Easy filling & air bleeding.
• Expandable to 2, 3 or 4 underfloor heating cir-

cuits.

Supplied with product

• Circulation pump Wilo Para RSB 15/6 SC, with 

automatic speed control.

• T

hermostat with capillary tube sensor, length 2 m.

• Thermometer to place in one of the shunt group's 

thermometer pockets.

•  Hose 0.5 m for air bleeding.
• Primary connector ¾" EuroCone and 2 connectors 

for CU15.

• Bracket.

Accessories

• Accessories for the primary connector include 

connectors  for CU12 mm and PEX-/PAL pipes 

dim. 16x2, 20x2 and 20x2.8.

• The LK Elbow Pipes M60n for connecting the 

primary connector when the feed pipe is from 

below or above. The elbow pipes enables compact 

assembly.

• Connection couplings for underfloor heating 

pipes dim. 8, 12, 16 and 20 mm.

• The LK Mini Manifold for 2, 3 or 4 underfloor 

heating circuits.

• Installation cabinets for built-in or wall mounting, 

see heading 

Installation cabinets.

• The LK Heater 350 is an electric comfort heater 

for underfloor heating installations using the  

LK Minishunt M60n. The electric heating car-

tridge output is 350W and is sufficient under 

normal conditions for underfloor heated areas  
up to 12 m².

LK Minishunt M60n circulation pump 

Wilo Para RSB 15/6 SC

EN.33.C.204.2022-02-10

Assembly instructions | LK Minishunt M60n

Summary of Contents for Minishunt M60n











Reviews:

No comments