LIXiSE LXC51 0 Series, User Manual

Page: 15 / 36

LXC63X0/LXC51X0 Generator controller user manual
Dongguan Tuancheng Automation Equipment Co.,LTD.
LXC63X0/LXC51X0 Generator controller user manual. Dongguan Tuancheng Automation Equipment Co.,LTD.
� :
T:+86 0769-23162896
� :
F:+86 0769-23166296
�
:::: www.lixise.com Page
15 of 36
� :
T:+86 0769-23162896
� :
F:+86 0769-23166296
�
:::: www.lixise.com Page
15 of 36
5.
5.
5. 5.
Protection
Protection Protection
Protection
5.1. 5.1. 5.1. 5.1. W W W Warning arning arning arnings s s s
When the controller detects warning signal, controller only warning does not stop, and the LCD display a
warning alarm type.
The following table warning volume controller:
No Warning type Description
1 High Temp. Warn
When controller detects the temperature is higher than the set value,it will
send a warn alarm signal and it will be displayed in LCD.
2
Low oil pressure
warn
When controller detects the oil pressure is lower than the set value,it will
send a warn alarm signal and it will be displayed in LCD.
3 Over Speed Warn
When controller detects the speed is higher than the set value,it will send a
warn alarm signal and it will be displayed in LCD.
4 Under Speed Warn
When controller detects the speed is lower than the set value, it will send a
warn alarm signal and it will be displayed in LCD.
5
Loss of Speed
Signal Warn
When controller detects the speed is 0 and the action select "Warn", it will
send a warn alarm signal and it will be displayed in LCD.
6
Over Frequency
Warn
When controller detects the frequency is higher than the set value,it will
send a warn alarm signal and it will be displayed in LCD.
7
Under Frequency
Warn When controller detects the frequency is lower than the set value,it will
send a warn alarm signal and it will be displayed in LCD.
8 Over Voltage Wan
When controller detects the voltage is higher than the set value,it will send
a warn alarm signal and it will be displayed in LCD.
9
Under Voltage
Warn
When controller detects the voltage is lower than the set value, it will send
a warn alarm signal and it will be displayed in LCD.
10 Over Current Warn
When controller detects the current is higher than the set value,it will send
a warn alarm signal and it will be displayed in LCD.
11 Fail to Stop
When generator cannot stop after the“stop delay”/”ETS delay”, controller
will send warning alarm signal and it will be displayed in LCD.
12 Low Level Warn
When controller detects the oil lever is lower than the set value, it will send
a warn alarm signal and it will be displayed in LCD.
13 Charge Alt Fail
When controller detects the charger voltage is lower than the set value, it
will send a warn alarm signal and it will be displayed in LCD.
14
Battery Under
Voltage
When controller detects the battery voltage is lower than the set value, it
will send a warn alarm signal and it will be displayed in LCD.
15
Battery Over
Voltage
When controller detects the battery voltage is higher than the set value, it will
send a warn alarm signal and it will be displayed in LCD.
16
Auxiliary input port
1-6 warning
When digit input port 1-6 is set as warning and active, controller sends
corresponding warning signal.
17 DTU bind failed
When setting the DTU and the controller binding, if the DTU is artificially
removed and disconnected from the controller, the controller will issue an
alarm, the alarm operation is performed after the user can set.
18
Load conversion
failed
Controller performs load switch, switch failure alarm is detected the alarm.
Note:
Note: Note:
Note:
the the the the auxiliary auxiliary auxiliary auxiliary input input input input port port port port warning warning warning warning types, types, types, types, must must must must be be be be user user user user configuration, configuration, configuration, configuration, to to to to be be be be effective effective effective effective....