Liquivision XEN User Manual Download | Manualshive

Page: 50 / 84

background image

Dive Computer

User Manual

Liquivision Products, Inc

-

50

-

Revision 3.2 Software 2.58

The green number in the lower-right-hand corner of the display is
your Current Depth.

Depth

If you chose metric units, you will see the depth in meters, with
one decimal place in smaller font.

If you chose imperial units, you will see the depth in feet, with no
decimal places.

Please refer to the “

Units

” section of the manual for details on choosing units.

The label “MAX” refers to the maximum depth you have reached over your entire dive. It is displayed
as a single number, without decimal places. It is displayed either in meters or in feet, depending on
your Units setting (refer to the “

Maximum Depth

Units

” section of the manual for details).

Your maximum depth will reset if you surface for more than the

Minimum Surface Interval

.

The horizontal section in the middle of the screen is reserved for your decompression information.
Each number in this section has an short name or label right above it. Here is a list of available data:

Decompression Information Zone

1. OC Dive With No Deco

2. CCR Dive With Deco

3. OC Dive With Deco

•

TTS – Time To Surface is total time it should take you to get to the surface, if you were to
precisely follow your XEO’s ascent schedule, including all the stops and recommended gas
switches. It is printed in minutes, and rounded up to the nearest minute.

•

NDL – No Decompression Limit is the maximum time you can still stay at your current depth,
before the XEO ascent schedule will include decompression stops. It is displayed in minutes,
and rounded down to the nearest minute.

•

STOP/FOR – Shown together (see Picture 2), this pair describes the deepest decompression
stop on your XEO’s ascent schedule. Below “STOP” there is depth of this stop (in meters or
feet, depending on your

Units

settings), and below “FOR” is its duration, in minutes, rounded

up to the nearest minute. If you are shallower than this stop, depth below “STOP” will be
blinking to remind you to go back deeper.

•

STOP – Shown as a stand alone value (see Picture 3), “STOP” shows the length of the deepest
decompression stop on your XEO’s ascent schedule when you are currently at this stop (that is,
within 0.5m / 1.6ft from it). It is displayed in minutes and seconds, rounded up to 10 seconds.

Depth

Deco Info Zone

Max Depth

«
...
48
49
50
51
52
...
»

Summary of Contents for XEN





















































































Reviews:

No comments

Related manuals for XEN

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 4

Brand: A&D Pages: 102

Brand: ABQ Industrial Pages: 15

Brand: ABQINDUSTRIAL Pages: 3

NUFLO Scanner 2000 microEFM

Brand: Cameron Pages: 8

PLATINUM Series

Brand: Hach Pages: 64

Brand: Unico Pages: 96

Brand: YOSensi Pages: 26

Brand: YOSensi Pages: 26

Brand: P3 International Pages: 1

Level Pro UltraPro 500 Series

Brand: Icon Process Controls Pages: 19

Dusty Harp Pickup Series

Brand: Dusty Strings Pages: 5

Brand: LEM Pages: 33

Brand: Omega Pages: 20

Brand: Bogen Pages: 14

Brand: Kurzweil Pages: 12

Brand: Scaletron Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands