Liquivision XEN User Manual Download | Manualshive

Page: 35 / 84

background image

Dive Computer

User Manual

Liquivision Products, Inc

-

35

-

Revision 3.2 Software 2.58

This allows you to control the minimum time of surface interval before next dive is classified as new
dive. If you stay on the surface for shorter time than the specified interval, your next descent will still
be considered a part of the previous dive, and both descents will be logged as one dive. You can control
this value in increments of 1 minute. Minimum value is 0, maximum – 30 minutes.

7.6. Minimum Surface Interval

If you tap into this menu setting, you will see basic information concerning
your device, such as type, hardware version, software version, etc.

7.7. Status

The type or capacity of the battery is needed to accurately estimate the remaining dive time.

7.8 Battery Type

There are three battery types available:

•

White-ER14335M (Disposable Lithium Battery)

•

Blue-ER17335M (High Capacity Disposable Lithium Battery)

•

White with green text-LFP-123A (Rechargeable Lithium-Iron-Phosphate Battery)

You can find more information about the different battery types in the section on

Important

Information About XEO Batteries.

This menu item allows you to select battery meter style either in battery symbol graphic or in battery
voltage value. The default setting is “Symbol”.

7.9 Battery Meter

Battery Meter: Symbol

Battery Meter: Voltage

This menu item runs the battery test for the selected battery type and displays the estimated remaining
dive time. This test will take approximately 1 minute. During the battery test, you will see the screen
light up progressively with white pixels, to provide a battery reading when the unit is at maximum
battery consumption.

7.10 Battery Test

«
...
33
34
35
36
37
...
»

Summary of Contents for XEN





















































































Reviews:

No comments

Related manuals for XEN

Brand: Landis+Gyr Pages: 10

Brand: Vanguard Instruments Pages: 24

Brand: Gardner Bender Pages: 7

Brand: K&M Analog Designs Pages: 10

Brand: Oceanic Pages: 68

Brand: Oceanic Pages: 24

Brand: Vega Pages: 20

Brand: Vega Pages: 16

Brand: Vega Pages: 2

Brand: KROHNE Pages: 56

Brand: LaserLiner Pages: 52

Brand: Veris Pages: 8

VIBRO-KING P/N 053493

Brand: Fender Pages: 8

Brand: YOSensi Pages: 27

Brand: Polimaster Pages: 6

Brand: STONEX Pages: 99

Brand: Nidec-Shimpo Pages: 6

Brand: Hanna Instruments Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands