manualshive.com logo in svg

LinMot E1450-DS-QN-0S, Installation Manual, Page: 16 / 27

Share
Download
LinMot E1450-DS-QN-0S Installation Manual Download Page 16

E1400 V2 Installation Guide

 7.15  X19

X19

System

1
2
3
4
5
6
7
8

case

Do not connect
Do not connect
RS232 Rx
GND
GND
RS232 Tx
Do not connect
Do not connect
Shield

RJ-45

Use 

isolated USB-RS232 converter (Art.-No. 0150-2473 

or 0150-3120

) 

for configuration over RS232.

 7.16  X20

X20

Analog In (+-10V Differential Analog Input)

1
2
3
4
5
6
7
8

case

Do not connect
Do not connect
Analog In -
GND
GND
Analog In +
Do not connect
Do not connect
Shield

RJ-45

 7.17  S5

S5

Bus Termination / AnaIn2 Pull Down

S5

Switch 6: Override Configuration Ethernet to DHCP
Switch 5: Bootstrap: Must be off for normal operation
Switch 4: CAN termination on ME (120R between pin 7 and 8 on X10/X11) on/off
Switch 3: CAN termination on CMD (120R between pin 7 and 8 on X7/X8) on/off
Switch 2: Termination resistor for RS485 on CMD (120R between pin 1 and 2 on X7/X8) on/off
Switch 1: AnIn2 pull down (4k7 Pull down on X4.4). Set to ON, if X4.4 is used as digital output.

Factory setting: all switches “on” except S5.5 (Bootstrap) and S5.6 (Override to DHCP)

Page 16/27

www.LinMot.com

NTI AG / LinMot

®

Summary of Contents for E1450-DS-QN-0S




























Reviews:

No comments