background image

 

5. OPERATION

 

 

5.1 Ramp Operation

 

1.

 

With  the  vehicle  in  park  and  the  parking  brake  se-

cured, open the rear door of the vehicle.

 

2.

 

Release  the  rotatory  latch  (midway  up  the  side  of  

ramp on the passenger side near the handle).

 

3.

 

Fold ramp out of the rear of the vehicle.

 

5.2 Ramp Swivel Out Operation 

 

1.

 

With the vehicle in park and the parking brake 

secured, open the rear door of the vehicle.

 

2.

 

To swivel the ramp out of vehicle.

 

3.

 

Release the latch on the passenger side of  vehicle 

by pulling the rear yellow handle  upward.

 

4.

 

Swing the ramp out till the ramp swivel lock en-

gages.

 

5.

 

To release ramp  pull the swivel lock and swing 

ramp until latched into latch. 

 

5.3 Ramp Swivel In Operation

 

1.

 

With the vehicle in park and the parking brake 

secured, open the rear door of the vehicle.

 

2.

 

To swivel the ramp into vehicle.

 

3.

 

Release the latch on the passenger side of  vehicle 

by pulling the forward yellow handle upward.

 

4.

 

Swing the ramp in till the ramp swivel lock engag-

es and the ramp is resting on the inside deck 

catch .

 

5.

 

To release ramp  pull the swivel lock and swing 

ramp outwards until latched into latch. 

 

 

6. MAINTENANCE

 

The LSR90 is designed to last for many years without any 

major maintenance. Periodically, check

 

the following items:

 

 

Each Time the Ramp is Used:

 

• 

Listen for unusual noises and watch to ensure prop-

er movement of the ramp.  If there is a problem, 

correct it before continuing to use the system.

 

 

Annually:

 

• 

Check tightness of all fasteners. (Refer to Torque 

Table below)

 

• 

Visually inspect for cracks or damage at all pivots 

on the framework and replace if necessary.

 

• 

Make certain the vehicle is in park and the parking 

brake is engaged before loading / unloading the vehi-

cle.

 

• 

Vehicle movement during loading / unloading could 

cause operator injury or death.

 

 

WARNING

 

• 

Loading beyond the capacity may result in equip-

ment damage or failure that may result in severe inju-

ry or death.

 

 

WARNING

 

• 

Do not use ramp if not locked into latch.  Damage or 

failure of ramp may occur that may result in severe 

injury or death.

 

 

WARNING

 

• 

Do not use ramp if not locked into latch.  Damage or 

failure of ramp may occur that may result in severe 

injury or death.

 

 

WARNING

 

• 

Park the vehicle in a level, flat area, 

and apply the parking brake before 

performing any maintenance.

 

 

CAUTION

 

TORQUE TABLE

 

FASTENER

 

TORQUE

 

3/8

-

UNC NUTS

 

30

-

40 FT

-

LBS

 

7/16

-

UNC NUTS

 

50

-

60 FT 

-

LBS

 

1/2

-

UNC NUTS

 

80

-

100 FT

-

LBS

 

Summary of Contents for LSR 90












Reviews: