background image

GENERAL

These luminaires are used where emergency 
light is needed. Each luminaire must be 
permanently connected to mains power 
supply

In normal operation the 

power

 and 

charge

 indicators are ON to indicate that the 

battery is charging. In case of a mains power 
supply failure the 

power 

and the 

charge

 

indicators turns off and the luminaire  will light 
the spot lamps automatically in emergency 
mode. When the mains power  supply is 
restored the device turns to normal operation.

INSTALLATION

To install the luminaire follow the installation 
instructions 

ο

n page 3.

OPERATION

When the device is powered from the mains

and the battery(ies) is(are) connected, the 
‘power’ and ‘charge’ indicators are ON. The 
‘charge’  indicator  indicates  the  battery 
charging  operation. 

If 

it  does 

not  li

gh

t, 

probably, the batter

ies are 

disconnected. If 

it 

does 

not  li

gh

t  and  the  batter

ies  are 

connected, then contact the technician. The

 

power

 

indicator 

confirms 

the 

proper 

connection to the 

mains

. The

 TEST butto

n, 

has a dual use. If pressed 

instantlly 

while the 

device is 

connected to the mains

, the device 

simulates the 

power interruption

by 

lighting 

the 

lamps for 

3

''. In th

at

 way

,

 we can control 

the driver circuit of 

the lamps 

and

 the 

lamps as 

indicated in paragraph 

3 in 

the text

 

below.

DIMMING OPTION

When the 

luminaire is in emergency mode

, with 

corresponding press

ing

s of the button,

 

we ca

choose 

the illumination of 100%, 50%, 33%  

or 

turned off

, either to increase the autonomy time 

or  not  to  consume 

the 

battery  power 

unnecessarily. This option is canceled when the 
network is restored.

ΑΤΤΕΝΤΙΟΝ!

!!

1. Operations for installation, maintainance or
    testing must be done by authorized
    personnel only

.

2. 

The device must be connected to the

    mains power supply through a fuse
    dependent by the total amount of the line’s 
    power load

.

3. 

It is suggested to check every month the

    indication LED for battery charging, and by
    pushing instantly the TEST button to check
    the emergency circuit and the lamps. If the
    luminaire does not light 

contact the

    installer. 

4. It is sug

g

ested to check every 6 months

    the minimum autonomy duration by
    disconnecting the mains power supply.
    Count the time that  the lamps light and in

Page 1 from 3

WATERPROOF NON MAINTAINED EMERGENCY LUMINAIRES

Aluminum, ABS/PC, PC

OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY

EXTERNAL DIMENSIONS 

CONSTRUCTION MATERIALS 

TYPICAL WEIGHT
GUARANTEE 

OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Pb)

CHARGING TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

LIGHT SOURCE

24h

Power indicator, battery charge indicator, TEST button

From overcharge and deep discharge

IP65

o

5 to 40 C

Up to 95% 

3 years 

(1 

year for the battery

)

180 min

90 min

  3200lm 

  White  power LEDs

6440gr.

4250gr.

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

220-240V AC/50-60Hz

2x12V/7Ah

12V/7Ah

307 x 100 x 350 mm.

TECHNICAL CHARACTERISTICS

 (

for LED MODULE Specifications see page 2)

DU239P13EGS

DU239P30EGS

13W/13.6VA

GB

LINERGY S.R.L.                                                         
VIA ALCIDE DE GASPERI, 9                
ACQUAVIVA PICENA (AP) 63075 ITALY 
TEL.: +39 0735 5974                                     
FAX: +39 0735 597474

www.linergy.it  [email protected]

ISTDUALLED_V2-R2

Reviews: