background image

4

13. TESTING TRANSMITTERS

15. LOCAL PROGRAMMING WITH RA-2400

14. ERASING TRANSMITTERS

16. TELEPHONE CONNECTIONS

218266 C     IMAGE 6

PRESS AND HOLD TEST BUTTON FOR 5 SECONDS
• 6 BEEPS SOUND (ALL TRANSMITTERS WERE ERASED)

1

CAUTION: ALL TRANSMITTERS

WILL BE ERASED!

PRESS CLEAR TO RETURN TO OPERATE MODE 
• 2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED
• 3 BEEPS SOUND WITH ACTIVITY TIMER DISABLED

THE CONSOLE WILL RETURN TO OPERATE MODE
AUTOMATICALLY AFTER 3 MINUTES

2

PRESS TEST BUTTON
MOMENTARILY
• 4 BEEPS SOUND 
  (TEST MODE)

NOTE: CONSOLE WILL EXIT TEST MODE
AUTOMATICALLY AFTER 3 MINUTES
OR BY PRESSING THE CLEAR BUTTON

2

3

WHEN RA-2400 CONNECTION
TIMER STARTS COUNTING DOWN,
PRESS THE EMERGENCY BUTTON
• 4 BEEPS SOUND
  (RA-2400 ANSWER)

1

TO LOCALLY PROGRAM
THE CONSOLE, CONNECT
THE MODEM'S LINE JACK
TO THE CONSOLE'S LINE
JACK

4

PERFORM THE STEPS DETAILED IN THE
RA-2400/PERS-2400 REFERENCE GUIDE (P/N 217163)
TO SET UP THE RA-2400 PROGRAM

LINE-TO-LINE

5

PERFORM PROGRAMMING IN
THE RA-2400 SOFTWARE, THEN
DISCONNECT FROM THE CONSOLE

CONNECT TELEPHONE
LINE TO THIS JACK

CONNECT LOCAL
TELEPHONE TO
THIS JACK

TELEPHONE
JACK

LOCAL
TELEPHONE

ROUTE CABLES UNDER
STRAIN-RELIEF TABS

CONSOLE WITH

REAR COVER

INSTALLED

3

2

1

PRESS TEST BUTTON
• 4 BEEPS SOUND (TEST MODE)

ACTIVATE EACH OF THE
CONSOLE'S TRANSMITTERS,
ONE AT A TIME

COUNT THE NUMBER OF BEEPS
THAT THE CONSOLE SOUNDS
WHEN THE TRANSMITTER
IS ACTIVATED

NOTE: WITH THE MODEL VB-4 VOICE BOARD
INSTALLED, THE CONSOLE WILL ANNOUNCE
THE TRANSMITTER STATUS

PRESS CLEAR TO RETURN TO OPERATE MODE
• 2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED
• 3 BEEPS SOUND WITH ACTIVITY TIMER DISABLED

THE CONSOLE WILL RETURN TO OPERATE MODE 
AUTOMATICALLY AFTER 3 MINUTES

4

1-BEEP   = TX OK
2-BEEPS = TX HAD ALARM
3-BEEPS = TX MISSED STATUS
4-BEEPS = TX HAS LOW BATTERY

firealarmresources.com

Summary of Contents for PERS2400A









Reviews: