background image

Lindsay Transportation Solutions Sales and Services, Inc 

(888) 800-3691 [U.S. toll free] or +1 (707) 374-6800

Lindsay Transportation Solutions Sales and Services, Inc

 (888) 800-3691 [U.S. toll free] or +1 (707) 374-6800

30

Appendix A -Bill of Materials - X-Lite Flared, MGS 37’ 6”

Item

Description

Full System Kit Only

BSI-1310024-00

XLITE,CRIMPED POST SLOTS,GALV

2.00

2.00

BSI-1310027-00

XLITE,CRIMPED POST HOLES,GALV

3.00

3.00

BSI-1012086-00

POST II, X-LITE, GALV

1.00

1.00

BSI-1012103-00

IMPACT HEAD,X-LITE, GALV

1.00

1.00

BSI-1012093-00

SLIDER PANEL,FRONT,XLITE,GALV

1.00

1.00

BSI-1012090-00

Slider Bracket, X-Lite

1.00

1.00

BSI-1012096-00

BACK SLIDER PANEL,X-LITE,GALV

1.00

1.00

BSI-1012097-00

Ground Strut, X-Lite

2.00

2.00

BSI-1012098-00

Ground Strut Angle

1.00

1.00

BSI-1012104-00

Cable Anchor Assembly, X-Lite

1.00

1.00

K080123

Kit, X-Tension Shear Bolt,

1.00

1.00

BSI-1102027-00

WASHER,SQUARE,X-LITE,GALV

1.00

1.00

B090534

W-Beam Composite Blockout 8in,

6.00

-

4001115

Guardrail Bolt 5/8-11x 1 1/4

24.00

-

2000302

Bolt CH 5/8-11 x 2”

1.00

-

2001635

Bolt CH 5/8-11 x 10”

6.00

-

4001116

Guardrail Nut Recessed 5/8-11

35.00

4.00

2001580

Wshr 1 F436 Structural Gal

1.00

1.00

4000443

W-Beam Guardrail RWM02a

3.00

-

BSI-1312100-00

Soil Plate

1.00

1.00

2000220

C-Scr HH 5/8-11x3 1/2

2.00

2.00

2001636

Wshr 5/8 F436   

4.00

4.00

2000312

Nut HX 5/8-11

2.00

2.00

BSI-1303005-00

Bracket, X-Lite, Cable Retenti

1.00

1.00

BSI-1310016-KT

Transition Kit, MGS, X-Lite

1.00

1.00

INSTALLATION MANUAL

Summary of Contents for Barrier Systems X-LITE

































Reviews: