Follow
these steps
to help increase the longevity and
usefulness of your OMNIShield®
face shield.
• Lightly blow off any loose dirt or debrisfrom
the lens
• Use a soft microfiber cloth or eyewear-
approved tissue to clean the lens
• Rinse your lenses with cool water and wipe
clean with lens-safe tissue
• Only use lens cleaning products to clean lenses
by spraying eyewear-specific cleaning solution
directly onto the lens and wipe clean with
lenssafe tissue
• Store face shield in a secure spot like a locker,
or shelving, but never on a table or around
your work area.
OMNISHIELD® FACE SHIELD
General Cleaning Guidelines
General Guidelines
WARNING
Maintenance And Storage
• Read and follow all steps set forth in the
OMNIShield® Operator’s Manual.
• Inspect face shield prior to each use. If there is
any sign of damage, such as pit marks, cracks,
scratches, or distortion, impact resistance is
severely reduced, OMNIShield® lens should be
replaced immediately.
• Never use solvents or abrasive cleaning
solutions to clean the OMNIShield®.
• Wash with mild detergent and warm water.
Rinse clean and remove excess water by patting
with soft tissue or cloth.
DO NOT
use ammonia,
alkaline cleaners, solvents, or abrasive cleaning
compounds, which may reduce visibility, impact
resistance and effectiveness of coatings.
• Cleaning is recommended after each use.
Important Notice:
• Follow your facility’s protocols for proper
disposal of cleaning equipment and solutions
OMNIShield® Lens Cleaning
Improper cleaning, poor handling and storage of
the OMNIShield® can result in reduced visibility,
impact resistance and effectiveness of coatings.
1.
To disassemble the lens, press the enclosed
button located in the center of the inside
headpiece. Rotate the lens so the locking pins
on each side of the headpiece align with the lens
notch in each corner. Then push each side of the
lens to detach from the headpiece.
2.
Use a warm, mild detergent cleaning solution.
3.
Wipe with a soft cloth until clean.
a.
DO NOT
use detergents that contain lanolin or
other oils, organic or chlorinated solvents or
abrasive cleaning agents. Rinsing OMNIShield®
Lens.
1.
Rinse the OMNIShield® lens by wiping with a
clean soft cloth, lightly dampened with clean
warm water, and thoroughly dry before use or
storage.
Important Notice:
• Ensure all components are dry prior to reuse or
storage.
• The cleaned OMNIShield® lens should be
carefully inspected per the OMNIShield®
Operator’s Manual.
OMNIShield® Headpiece Cleaning
Improper cleaning, poor handling and storage
of the OMNIShield® all result in reduced impact
resistance.
1.
Disassemble the headpiece from the lens.
2.
Use a warm, mild detergent cleaning solution.
3.
Wipe with a soft cloth until clean.
a.
DO NOT
use detergents that contain lanolin or
other oils, organic or chlorinated solvents or
abrasive cleaning agents. Rinsing OMNIShield®
Headpiece.
1.
Rinse the OMNIShield® lens by wiping with a
clean soft cloth, lightly dampened with clean
warm water, and thoroughly dry before use or
storage.
Disinfecting Safety Glasses & Goggles Lens.
1. Disinfect the Safety Glasses & Goggles lens by
wiping with a suitable disinfecting material
recommended by the EPA after drying and
before use:
https://www.epa.gov/pesticide-
registration/selected-eparegistered-
disinfectants
.
Important Notice:
• Ensure all components are dry prior to reuse or
storage.
• The cleaned OMNIShield® headpiece should
be carefully inspected per the OMNIShield®
Operator’s Manual.
The Lincoln Electric Company
22801 St. Clair Avenue
Cleveland, OH 44117-1199 U.S.A.
www.lincolnelectric.com/helmets
OMNIShield
®
Face Shield
General Cleaning Guidelines
Issue Date 07/2020
© Lincoln Global Inc. All Rights Reserved.
User’s Guide
KPXXXX-1
Maintenance And Storage
• Read and follow all steps set forth in the OMNIShield® Operator’s Manual.
• Inspect face shield prior to each use. If there is any sign of damage, such as pit marks,
cracks, scratches, or distortion, impact resistance is severely reduced, OMNIShield®
lens should be replaced immediately.
• Never use solvents or abrasive cleaning solutions to clean the OMNIShield®.
• Wash with mild detergent and warm water. Rinse clean and remove excess water by
patting with soft tissue or cloth. DO NOT use ammonia, alkaline cleaners, solvents, or
abrasive cleaning compounds, which may reduce visibility, impact resistance and
effectiveness of coatings.
• Cleaning is recommended after each use.
IMPORTANT NOTICE:
• Follow your facility’s protocols for proper disposal of cleaning equipment and solutions.
OMNIShield
®
Lens Cleaning
Improper cleaning, poor handling and storage of the OMNIShield® can result in
reduced visibility, impact resistance and effectiveness of coatings.
1. To disassemble the lens, press the enclosed button located in the center of the inside
headpiece. Rotate the lens so the locking pins on each side of the headpiece align with the
lens notch in each corner. Then push each side of the lens to detach from the headpiece.
2. Use a warm, mild detergent cleaning solution.
3. Wipe with a soft cloth until clean.
a. Do not use detergents that contain lanolin or other oils, organic or chlorinated solvents or
abrasive cleaning agents.
Rinsing OMNIShield® Lens.
1. Rinse the OMNIShield® lens by wiping with a clean soft cloth, lightly dampened with clean
warm water, and thoroughly dry before use or storage.
IMPORTANT NOTICE:
• Ensure all components are dry prior to reuse or storage.
• The cleaned OMNIShield® lens should be carefully inspected per the OMNIShield® Operator’s
Manual.
OMNIShield
®
Headpiece Cleaning
Improper cleaning, poor handling and storage of the OMNIShield® all result in reduced
impact resistance.
1. Disassemble the headpiece from the lens.
2. Use a warm, mild detergent cleaning solution.
3. Wipe with a soft cloth until clean.
a. Do not use detergents that contain lanolin or other oils, organic or chlorinated solvents or
abrasive cleaning agents.
Rinsing OMNIShield® Headpiece.
1. Rinse the OMNIShield® lens by wiping with a clean soft cloth, lightly dampened with clean
warm water, and thoroughly dry before use or storage.
IMPORTANT NOTICE:
• Ensure all components are dry prior to reuse or storage.
• The cleaned OMNIShield® headpiece should be carefully inspected per the OMNIShield®
Operator’s Manual.
WARNING
General Guidelines
Follow these steps to help increase the longevity
and usefulness of your OMNIShield® face shield.
• Lightly blow off any loose dirt or debris
from the lens
• Use a soft microfiber cloth or eyewear-approved
tissue to clean the lens
• Rinse your lenses with cool water and wipe
clean with lens-safe tissue
• Only use lens cleaning products to clean lenses
by spraying eyewear-specific cleaning solution
directly onto the lens and wipe clean with lens-
safe tissue
• Store face shield in a secure spot like a locker,
or shelving, but never on a table or around your
work area.
