manualshive.com logo in svg

Lincoln Electric FineLine BK300370, Operator'S Manual, Page: 40 / 46

Share
Download
Lincoln Electric FineLine BK300370 Operator'S Manual Download Page 40

FineLine Advanced Process Controller 

BK8053-000117 Rev B 

This information is subject to the controls of the Export Administration Regulations [EAR]. This information shall not be provided to 

non-U.S. persons or transferred by any means to any location outside the United States contrary to the requirements of the EAR. 

Page 40 of 46 

6.2 Hoses and Cables 

6.2.1 Pierce Head Hose 

Part Number 

Length 

BK300384 

9 ft (2.7m) 

6.2.2 Power Adapter Cable 

Part Number 

Length 

BK300381 

16 inches (406mm) 

6.2.3 RS-485 Communication Cable 

Part Number 

Length 

BK300376 

16 inches (406mm) 

6.2.4 Ethernet Cable w/ Bayonet 

Part Number 

Length 

K4907-XX 

Where -XX is the length in feet. 

-25, -50, -75, -100, -125 ft. lengths available. 

6.2.5 Water Shield Hose 

Part Number 

Length 

BK300378 

8 inches (203mm) 

6.2.6 Water Inlet Hose 

Part Number 

Length 

BK300382-XX 

Where -XX is the length in feet. 

-25, -50, -75, -100, -125 ft. lengths available. 

6.2.7 Water Supply Hose 

Part Number 

Length 

BK300387-25 

25 ft. (7.62m) 

6.2.8 Air Supply Hose 

Part Number 

Length 

BK200364-XX 

Where -XX is the length in feet. 

-25, -50, -75, -100, -125 ft. lengths available. 

Summary of Contents for FineLine BK300370















































Reviews:

No comments