manualshive.com logo in svg

Limerick Joy, Owner'S Manual

Introducing the Arnica Joy! Access the comprehensive Instruction Manual easily with just a simple download. This invaluable manual is available for free, exclusively at manualshive.com. Discover everything you need to know about operating your Arnica Joy and unleash its full potential for utmost enjoyment and satisfaction.

Share
Download
background image

Page 8

Accessory Kit Sanitizing

Accessory Kit Sanitizing

Before using the accessory kit for the first time

       

Caution!

 Unless there is a label stating 

sterile 

on the kit, the 

accessory kit is not supplied sterile. It’s not necessary that the parts 
be sterile, but some must be sanitized before the first time you use 
the pump. After the first time you use the pump, the accessories will 
only need a simple cleaning procedure, 

see page 31-5

.

DO NOT BOIL THESE PARTS

The filter, tubing, connector, clamp, and “Y” connector do not need 
to be sanitized as air is all that flows through the parts. The filter is 
designed to last the duration of your current breast-feeding goals. 
See “Caution” 

on page 25

 to prevent clogging.

clear tubing (12)

filter 

(9)

white  

silicone 

tubing (10)

Y 

connector  

(11)

tube  

connector  

(13)

tube  

clamp 

(19)

Summary of Contents for Joy














































Reviews:

No comments

Related manuals for Joy

Brands by name

Popular brands

Load more brands