P
art Description & Dimensions
D/N HD IR IP CAMERA
66-8822CSB-1B
Installation Guide
189mm
69mm
176mm
74mm
1
2
3
76mm
φ
58
φ
70
φ
58
3-120°
5
3
6
7
4
Front Cover
Main Body
Bracket Base
Window
1
2
3
4
I
nstallation
1. Retrieve the camera from the box first. Connect the Ethernet cable and power
cable to the camera’s RJ-45 network connector and DC power-in connector
(FIG.1). Secure the camera (FIG.2).
Note: For outdoor installation, it is recommended to install a waterproof
junction box.
FIG.1
FIG.2
Network Cable
DC Power Input
Connect the RJ-45 Ethernet cable with a waterproof connector
First, remove the waterproof connector and unscrew the waterproof nut.
Insert the Ethernet cable and connect to the RJ-45 connector with proper
tools (FIG.3). Then, tighten the waterproof connector and nut before the
RJ-45 connector is connected to the camera (FIG.4).
FIG.3
FIG.4
2. Adjust the five adjustment screws to move the camera to the desired angle,
and then tighten the adjustment screws (FIG.5~10).
FIG.5
FIG.6
FIG.7
FIG.8
FIG.9
FIG.10
I
nserting a Micro SD Card
First remove the screw under the front cover, then rotate the front cover
counterclockwise to remove it and insert a Micro SD card (FIG.11 & 12).
FIG.9
FIG.10
For connecting IP Camera series to the network, please follow one of the
system architectures:
(1). Use DC12V power adaptor and network switch connected to a network.
S
ystem Architectures
PoE Switch
PC
LAN
LAN / Internet
PC
LAN
LAN / Internet
Non-PoE Switch
DC12V Adaptor
(2). Use with PoE of the network switch connected to the network.
IP CAMERA
(3). Use PoE power injector and the network switch connected to the network.
PoE Power Injector
PC
LAN
LAN / Internet
AC
Non-PoE Switch
LAN
IP CAMERA
IP CAMERA
Micro SD card slot
Factory default button
Lens
5
6
7
Audio OUT
GND
Audio IN
GND
Alarm IN
COM
Alarm OUT
AUDIO
ALARM
[AF IR IP Camera Only]
L
ogin
The factory default username and password are empty. To login to the Full
HD IP camera, please set the username and password on the login page.
Press [Login] to complete the setting and login simultaneously.
Password have to meet the following criteria:
1. More than or equal to 8 characters.
2. Allow uppercase letter, lowercase letter, number digit, and special
character.
3. Must have at least three types of character sets.
Before accessing the IP camera, make sure that the camera's RJ-45
network, audio, and power cables are properly connected. To set the IP
address, consult your network administrator for an available IP address.
The default IP address for each IP camera is 192.168.0.200. Users can use
the default IP address for verifying the camera's network connection.
B
efore Accessing IP Cameras
To change the settings of the IP address, subnet mask, gateway, or HTTP
port, you can follow the steps below:
1. Run the IPScan software.
2. Click
Refresh
. All available devices should be listed in the device list.
3. Select your device from the list provided.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP
camera.
5. Click
Apply
to submit the settings.
6. Click
Refresh
to verify the settings.
C
onfiguring IP Addresses with IPScan Software
IPCAM
To restore the hardware to factory default settings, please follow these steps:
1.Press and hold “RESET Key” for 10 seconds and release.
2.Wait for about 40 seconds, and the network LED light should turn off, and
go back on again.
3.The camera is now restored to factory default settings, and will reboot
automatically.
4.Search for the IP device using the IPScan software.
5.Start the IP device via an Internet browser.
6.Enter the username and password to operate.
The factory default username and password are empty, and the
user can set an account for login.
The IP address will revert to the default setting of 192.168.0.200.
NOTE1:
NOTE2:
E
mergency Factory Default
To change an IP address via web interface, type the default IP address
(192.168.0.200) in the Internet browser and follow the steps below:
1. Login to the Full HD IP camera with the set username and password.
2. Click
Basic Mode
configuration hyperlink.
3. Click
Network->General
hyperlink
.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP
camera.
5. Click
Submit
to verify the settings.
C
onfiguring IP Addresses via Web Interface
Universal ActiveX software components are required for web interface
display of JPEG or Full HD video. When you login to the IP camera by
Internet Explorer, the security warning dialog box will prompt the
installation of the Universal ActiveX. Click
Install
to download it.
S
oftware Requirements
