Instruction Manual
Part Description & Dimensions
AHD DOME IR CAMERA
Unit: mm
66-AHD612ACSE-1
Installation
1
2
5
6
145.0
3
4
10.0
78.7
130.0
7
8
1
BOTTOM CHASSIS
TOP COVER
BOTTOM HOLE
SIDE HOLE
2
3
4
INNER COVER
DOME COVER
LENS
HOLE PLUG
5
6
7
8
1. Please use the enclosed hexagon screwdriver to loosen the 4 screws on the top cover (FIG.1).
2. Use a screwdriver to loosen the 3 screw on the camera module (FIG.2)
3. Secure the safety cable on the bottom chassis with a screwdriver (FIG.3). Put the provided screws (M4.0
x25, Truss head screw) through the holes marked as “a”,
secure the bottom chassis to the desired
area (FIG.4 & FIG.5)
and
5. Use the screwdriver to secure the camera module to the bottom chassis (FIG.8).
4. Firstly, insert video cable and power cables through a pipe with 1/2
" PT at one end (FIG.6), and then
secure the pipe to the side hole or bottom hole (FIG.7, please make sure the connection between
the pipe and the side hole or bottom hole is watertight.).
NOTE: Pipe is not provided.
FIG.6
FIG.7
C
a
m
e
ra
M
o
d
u
le
FIG.3
FIG.4
FIG.5
a
66mm
120
°
a
6. Plug the power cable to the jack and plug the video cable to the video output of the camera
(FIG.9). For safety, when plugging the video cable to the video output, be sure to use the cable
tubing (Accessory) to cover the joint of connection to avoid danger of electric shock or
electric leakage (FIG.10).
Video Output
Video Cable
Cable Tubing
7. Remove the inner cover from the camera module (FIG.11), and then adjust the direction of
the lens with the adjustable Pan/Tilt bracket and the rotatable round bracket for Azimuth
(FIG.12).
PAN
TILT
AZIMUTH
8. Rotate the screws to adjust the focus and zoom of the lens to optimize image quality (FIG.13).
Z O O M
F O C U S
FIG.1
FIG.2
FIG.9
FIG.10
FIG.11
FIG.12
Camera
Module
FIG.8
Press inward
and pull down
.
FIG.13
9. Put on the inner cover (FIG.14), and fix the safety cable on the top cover with a screwdriver
(FIG.15). Replace the top cover and tighten the screws (FIG.16).
a
FIG.14
FIG.15
FIG.16
10. Connect to an Up-the-Coax (UTC) digital recorder that supports AHD-Coaxial protocol. Then
use the 8-directional buttons (FIG.17) to adjust settings for the best images.
SET
UP
DOWN
RIGHT
LEFT
10-1. USER OSD SETTING
A.
(UP)
B.
(LEFT)
C.
(RIGHT)
D.
(DOWN)
E. SET : Executes selections and displays a submenu for an item with the
mark.
: Press to move the cursor upwards or to select items.
: Press to move the cursor to the left and to select or adjust the
parameters of the selected item.
The parameters changes each time this button is pressed.
: Press to move the cursor to the right and select or adjust the
parameters of the selected item. The parameters changes each
time this button is pressed.
: Press to move the cursor downwards or to select items.
FIG.17
Alternative Cabling positions
1. Loosen the hole plug on the bottom hole of the bottom chassis and secure it to the side
hole with screws (FIG.18).
2. Insert the video cable and power cable through the bottom hole. Then connect them to the
video output and power input of the camera. Please refer to INSTALLATION Step 4 for water
resistant installation (FIG.19).
