Lika MTA1 User Manual Download | Manualshive

Page: 10 / 48

background image

SMA1

1.3 Mechanical safety

•

Install the device following strictly the information in the “3 - Mounting

instructions” section on page 11;

•

mechanical installation has to be carried out with stationary mechanical

parts;

•

do not disassemble the unit;

•

do not tool the unit;

•

delicate electronic equipment: handle with care; do not subject the device

to knocks or shocks;

•

protect the unit against acid solutions or chemicals that may damage it;

•

respect the environmental characteristics of the product;

•

we suggest installing the unit providing protection means against waste,

especially swarf as turnings, chips, or filings; should this not be possible,
please make sure that adequate cleaning measures (as for instance
brushes, scrapers, jets of compressed air, etc.) are in place in order to
prevent the sensor and the magnetic scale from jamming.

2 - Identification

Device can be identified through the

order code

and the

serial number

printed

on the label applied to its body. Information is listed in the delivery document
too. Please always quote the order code and the serial number when reaching
Lika Electronic for purchasing spare parts or needing assistance. For any
information on the technical characteristics of the product refer to the
technical datasheet.

Warning

: devices having order code ending with "/Sxxx" may have

mechanical and electrical characteristics different from standard and
be supplied with additional documentation for special connections
(Technical Info).

MAN SMA1 E 2.9.odt

2 - Identification

10 of 48

«
...
8
9
10
11
12
...
»

Summary of Contents for MTA1

















































Reviews:

No comments

Related manuals for MTA1

SO ROAD MOVIE CAR PACK

Brand: DANE-ELEC Pages: 14

Brand: DANE-ELEC Pages: 2

Brand: DANE-ELEC Pages: 16

Brand: DANE-ELEC Pages: 16

Brand: DANE-ELEC Pages: 2

SO XSTREAM FULL HD -

Brand: DANE-ELEC Pages: 2

Brand: Enerdrive Pages: 24

AURORA PVI-3.0-OUTD-S-US

Brand: Power One Pages: 108

MediaServer MS5000

Brand: Imerge Pages: 68

RASPTOUCH ES9018K2M

Brand: Audiophonics Pages: 30

Brand: Tvone Pages: 13

Brand: Patton electronics Pages: 7

Brand: Sencore Pages: 126

Brand: StarTech.com Pages: 4

Brand: B&B Electronics Pages: 2

Brand: Solplanet Pages: 75

Brand: EASYLITE Pages: 44

Brand: PNI Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands