Lightware UBEX-PRO20-HDMI-F100, User Manual, Page: 25 / 185

3. Front Panel LCD Menu Operations series – Extender Application Mode – User's Manual 25 3. Front Panel LCD Menu Operations series – Extender Application Mode – User's Manual 25
EXTENDER APPLIC
A
TION MODE
Applied F-series endpoint firmware package: v2.0.0 | Applied R-series endpoint firmware package: v2.0.0 | LDC software: v2.5.9b3
3.4.3. TX O1 and TX O2 Ports
The following information is displayed for both local output ports:
▪
HDCP mode
- Auto / Always / Force 2.2 Type1
▪
Output 5V mode
- Always on / Auto / Always off
▪ Hotplug detect
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
#hdcp #power5v
3.5. Ports Menu - Receiver Operation Mode
The most important settings and status information of the HDMI output ports
are available in the Ports menu.
The four local HDMI ports and the remote HDMI ports of the connected device
are listed in the Ports menu of the receiver.
INFO: The displayed remote ports depend on the operation mode of the
connected remote device. It is different when the connected device is a
transmitter or a transceiver.
Local ports
Remote ports if the connected
device is TRANSMITTER (TX)
Remote ports if the connected
device is TRANSCEIVER (TRX)
RX O1 TX I1 TRX I2
RX O2 TX I2 TRX O1
RX I1
RX I2
Select the desired input or output port and enter to see the submenus.
3.5.1. TX I1 and TX I2 Ports
INFO: The following port status information is related to the remote input ports of the transmitter.
HDMI Input
The following information is displayed in the case of both input ports of the transmitter:
▪ +5V present
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
Stream Output
The following information is displayed in the case of both input ports of the transmitter:
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
3.5.2. RX O1 and RX O2 Ports
Stream Input
The following settings and information are related to the stream coming from the input ports of the connected
device:
▪
Stream enable
- Enabled / Disabled #streamenable
▪
Stream source
- TX HDMI input 1 / TX HDMI input 2 #switch #crosspoint
▪
Signal present
▪
Active resolution
▪
Total resolution
▪
Color space
Video Settings
The following settings can be set in the case of both output ports:
▪
Resolution mode
#scaler #frc
– Passthrough: pass-through mode; the original resolution of the stream is transmitted.
– Forced: the resolution which is set in the Resolution setting menu is forced.
– EdidBased: the resolution which is read out from the EDID of the connected sink device is forced.
▪
Resolution setting
- select a resolution to force from the pre-installed list. The entire list can be found in
the Resolutions of the Scaler / FRC section.
▪
Image position
- Center / Fit / Stretch
INFO: The Image position setting on the HDMI out 2 port is a read-only parameter and fixed as
Center
.
▪
Color space
- Passthrough / Force RGB / Force YCbCr 4:4:4 / Force YCbCr 4:2:2 #csc #colorspace
▪
No Sync mode
- the No sync mode feature generates an image which can be displayed when there
is no incoming signal on the port. The following settings can be set for the Test Pattern function:
#testpattern #nosyncscreen
–
Always off
- the test pattern function is disabled, the video output port transmits the video signal of the
selected input port.
–
No signal mode
- the video output port transmits the test pattern if there is no incoming signal on
the selected input port.
–
Always on
- the video output port always transmits the test pattern.
–
Freeze
- the signal freezes at the last video frame on the sink device (the sink may show a broken
frame either). #freeze

  

  