Lightware UBEX-MMU-X200, User Manual, Page: 62 / 253

6. UBEX Concept series – Matrix Application Mode – User's Manual 62 6. UBEX Concept series – Matrix Application Mode – User's Manual 62
MA
TRIX APPLIC
A
TION MODE
Applied F-series endpoint firmware package: v1.5.4 | Applied R-series endpoint firmware package: v1.5.4 | Applied MMU firmware package: v1.3.3 | LDC software: v2.4.2b4
6.3.2. Receiver Mode
Port Diagram
The port diagram is valid for the following UBEX endpoint models:
▪
UBEX-PRO20-HDMI-F100
▪
UBEX-PRO20-HDMI-F110
▪
UBEX-PRO20-HDMI-R100 series
Video port diagram of the F100/F110/R100 receiver
Fiber Optical Interface
The receiver can receive two HDMI video streams via the fiber optical input ports.
HDMI Output Modes
The receiver can transmit HDMI video streams on two HDMI 2.0 output ports. The signal can be up to
4K@60 Hz 4:4:4 in the case of both outputs. The streams received from the remote endpoint device can be
routed to any HDMI outputs of receiver, e.g. the stream from the TX - HDMI in 1 can be switched to the RX -
HDMI out 1 or 2, or both ones either.
The streams can be processed by the video processors. The processor of the HDMI out 1 has
video scaler
,
frame rate converter (FRC)
, and
color space converter (CSC)
functions. The processor of the HDMI out 2 has
frame
rate converter
and
color space converter
functions.
The scaler, frame rate converter, and color space converter settings are available in the LDC software (see
the details in the Video Destination Port Properties Window or in the HDMI Output Ports section).
Source Multiplexer (MUX)
The source multiplexer (
Source MUX
) makes available routing more different source signals to the HDMI
output ports. The type of sources is different for the two outputs.
HDMI out 1
▪ Able to accept signal up to 4K@60 4:4:4 resolution
via the SFP+ links
from the remote endpoint device;
▪ Able to accept signal up to 4K@60 4:4:4 resolution
via the local HDMI in 1
port.
HDMI out 2
▪ Able to accept signal up to 4K@60 4:4:4 resolution
via the SFP+ links
from the remote endpoint device;
▪ Able to accept signal up to 4K@60 4:4:4 resolution
via the local HDMI in 2
port;
▪ Able to
copy the signal of the HDMI out 1
port up to 4K@60 4:4:4 resolution. This is the
COPY
function.
ATTENTION! If the selected source is the local input port or the copy of the HDMI out 1, the output is still
selectable as a destination in the global crosspoint table. It means the crosspoint setting is not forbidden
for the selected output and it is still included in the bandwidth calculation. When the sum of the two
incoming streams exceeds the bandwidth limit, the signal transmission can be denied on the HDMI out 2
port even if the incoming stream of the HDMI out 1 is not used. The solution of this limitation is disabling
of the unused destination port.
HDMI Input Modes
The HDMI input ports of the receiver operate as local HDMI inputs. The stream cannot be affected by any
video processing.
Summary Tables
HDMI INPUTS
HDMI input 1 HDMI input 2
Accepted signal up to 4K@60 4:4:4 up to 4K@60 4:4:4
Signal sink HDMI out 1 HDMI out 2
HDMI OUTPUTS
HDMI output 1 HDMI output 2
Output signal up to 4K@60 4:4:4 up to 4K@60 4:4:4
Signal source
MUX
Selected input port of the
remote device
MUX
Selected input port of the
remote device
Local HDMI in 1
Local HDMI in 2
Copy of the HDMI out 1
Scaler
 
-
Frame rate converter (FRC)
   
Color space converter (CSC)
   

  

  