Home
/
Lightware
/
UBEX-MMU-X200
/
User Manual

Lightware UBEX-MMU-X200, User Manual, Page: 142 / 253

Share

Page: 142 / 253

Lightware UBEX-MMU-X200 User Manual Download Page 142

9. Programmer's Reference

series – Matrix Application Mode – User's Manual

142

9. Programmer's Reference

series – Matrix Application Mode – User's Manual

142

MA

TRIX APPLIC

A

TION MODE

Applied F-series endpoint firmware package: v1.5.4 | Applied R-series endpoint firmware package: v1.5.4 | Applied MMU firmware package: v1.3.3 | LDC software: v2.4.2b4

9.7.10. Query the Claiming Status of an Endpoint

Command and Response

ç

GET•/SYS/ENDPOINTS/

<UBEX_EP>

.ClaimingStatus

æ

pr•/SYS/ENDPOINTS/

<UBEX_EP>

.ClaimingStatus=

<status>

Parameters

Parameter

Parameter description

Value

Value description

<status>

Claiming status of the

selected endpoint

Unclaiming

The device is under the unclaiming

procedure, it can be after the running of the

unclaimEndpoint()

or

unclaimAllEndpoint()

commands typically.

Initializing

The device is under initialization, it can

be during the first connecting to the MMU

typically.

Claiming

The device is under the claiming procedure.

Reclaiming

The device is under the reclaiming

procedure, it can be after operation mode

changing typically.

Restoring

The device is under the restoring procedure,

it can be during rebooting of a claimed

endpoint device.

Claimed

The device is claimed by the MMU and

ready to use in the UBEX matrix.

Example

ç

GET /SYS/ENDPOINTS/UBEX0039A1.ClaimingStatus

æ

pr /SYS/ENDPOINTS/UBEX0039A1.ClaimingStatus=Claimed

9.7.11. Unclaiming an Endpoint

The command makes the selected endpoint to be unclaimed from the UBEX matrix.

Command and Response

ç

CALL•/SYS/ENDPOINTS:unclaimEndpoint(

<UBEX_EP>

)

æ

mO•/SYS/ENDPOINTS:unclaimEndpoint=

Example

ç

CALL /SYS/ENDPOINTS:unclaimEndpoint(UBEX0039A1)

æ

mO /SYS/ENDPOINTS:unclaimEndpoint=

9.7.12. Unclaiming All Endpoints

The command makes all endpoints to be unclaimed from the UBEX matrix.

Command and Response

ç

CALL•/SYS/ENDPOINTS:unclaimAllEndpoint()

æ

mO•/SYS/ENDPOINTS:unclaimAllEndpoint=

Example

ç

CALL /SYS/ENDPOINTS:unclaimAllEndpoint()

æ

mO /SYS/ENDPOINTS:unclaimAllEndpoint=

9.7.13. Query the Number of the Mapped Endpoints

The query returns the number of mapped endpoint which got a logical device ID. This number is equal with

the result of the

Query the Number of Registered Endpoints

Command and Response

ç

GET•/MEDIA/DEVICEMAP.MappedEndpointCount

æ

pr•/MEDIA/DEVICEMAP.MappedEndpointCount=

<number>

Example

ç

GET /MEDIA/DEVICEMAP.MappedEndpointCount

æ

pr /MEDIA/DEVICEMAP.MappedEndpointCount=45

9.7.14. Query the Endpoint ID of a Logical Device ID

The query returns with the UBEX endpoint ID assigned to the selected logical device ID.

Command and Response

ç

GET•/MEDIA/DEVICEMAP.

<logical_device_ID>

æ

pr•/MEDIA/DEVICEMAP.

<logical_device_ID>

=

<UBEX_EP>

Example

ç

GET /MEDIA/DEVICEMAP.X1

æ

pr /MEDIA/DEVICEMAP.X1=UBEX0039A1





 





 

«
...
140
141
142
143
144
...
»

Summary of Contents for UBEX-MMU-X200






























































































































































































































































Reviews:

No comments