manualshive.com logo in svg

Lightware HDMI-3D-OPT-RX150RA, User Manual

Share
Download
Lightware HDMI-3D-OPT-RX150RA User Manual Download Page 61

 

7. LW3 Programmer's Reference

 

HDMI-3D-OPT series – User's Manual 

61

7.6.14. 

Unmute Output

Command format

:  

CALL

●

/MEDIA/VIDEO/XP:unmuteDestination(<O

n

>)

Response format

:  

mO

●

/MEDIA/VIDEO/XP:unmuteDestination

Example

:

 

˃

CALL /MEDIA/VIDEO/XP:unmuteDestination(O1)

 

˂

mO /MEDIA/VIDEO/XP:unmuteDestination

7.6.15. 

Lock Output

Command format

:  

CALL

●

/MEDIA/VIDEO/XP:lockDestination(<O

n

>)

Response format

:  

mO

●

/MEDIA/VIDEO/XP:lockDestination

Example

:

 

˃

CALL /MEDIA/VIDEO/XP:lockDestination(O1)

 

˂

mO /MEDIA/VIDEO/XP:lockDestination

7.6.16. 

Unlock Output

Command format

:  

CALL

●

/MEDIA/VIDEO/XP:unlockDestination(<O

n

>)

Response format

:  

mO

●

/MEDIA/VIDEO/XP:unlockDestination

Example

:

 

˃

CALL /MEDIA/VIDEO/XP:unlockDestination(O1)

 

˂

mO /MEDIA/VIDEO/XP:unlockDestination

7.6.17. HDCP Setting (Input Port)

HDCP capability can be enabled/disabled on the input ports, thus, non-encrypted content can be seen on a 

non-HDCP compliant display. See more information in the 

HDCP Management

 section.

Command format

:  

SET

●

/MEDIA/VIDEO/<I

n

>.HdcpEnable=true|false

Response format

:  

pw

●

/MEDIA/VIDEO/<I

n

>.HdcpEnable=true|false

Example

:

 

˃

SET /MEDIA/VIDEO/I2.HdcpEnable=true

 

˂

pw /MEDIA/VIDEO/I2.HdcpEnable=true

7.6.18. HDCP Setting (Output Port)

HDCP  capability  can  be  set  to  Auto/Always  on  the  output  ports,  thus,  non-encrypted  content  can  be 

transmitted to a non-HDCP compliant display. See more information in the 

HDCP Management

 section.

Command format

:  

SET

●

/MEDIA/VIDEO/<O

n

>.HdcpModeSetting=0|1

Response format

:  

pw

●

/MEDIA/VIDEO/<O

n

>.HdcpModeSetting=0|1

Parameters

:

.HdcpModeSetting

0

1

HDCP mode

Auto

Always

Example

:

 

˃

SET /MEDIA/VIDEO/O1.HdcpModeSetting=0

 

˂

pw /MEDIA/VIDEO/O1.HdcpModeSetting=0

7.6.19. 

Test Pattern Generator

The output ports can send a special image towards the sink devices for testing purposes. The setting is 

available on output ports with the below-listed parameters.

ATTENTION! 

The Mode can be set individually on each port, but the Clock source and the Pattern settings 

are common on the optical and HDMI output ports (O1 and O2).

Test Pattern Generator Mode Setting:

Command format

:  

SET

●

/MEDIA/VIDEO/<O

n

>.TpgMode=0|1|2

Response format

:  

pw

●

/MEDIA/VIDEO/<O

n

>.TpgMode=0|1|2

Parameters

:

.TpgMode

0

1

2

Test pattern generator 

mode

Disabled

 

The test pattern is not 

displayed on the output

Enabled

 

The test pattern is 

displayed on the output

No signal mode

 

The test pattern is 

displayed if there is no 

signal on the output port

Example

:

 

˃

SET /MEDIA/VIDEO/O1.TpgMode=2

 

˂

pw /MEDIA/VIDEO/O1.TpgMode=2

 

Summary of Contents for HDMI-3D-OPT-RX150RA


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands