manualshive.com logo in svg

Lightware 91540021, User Manual

Share
Download
Lightware 91540021 User Manual Download Page 48

 

5.SoftwareControl-LightwareDeviceController

HDMI-TPS-RX110AYseries–User'sManual

48

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

5.10. 

The Built-in Miniweb

Thedefaultcontrolpageallowsthefollowings:

 

▪

Source selection: 

This block can be used to select an input or 

enable/disable the Autoselect remotely e.g. from a mobile

device.

 

▪

Action triggers: 

The action trigger buttons can be used to perform 

aconfiguredEventActionwithoutwaitingfortheconditionto

occur. This can be done remotely by a mobile device, too.

5.10.1. 

Opening the Miniweb

TheMiniwebisavailableby:

 

▪

Opening the 

web browser 

and typing the 

IP address 

of the desired 

device in the address line,

 

▪

Launching the

LDC

, connecting to the device, navigating to 

Settings/Status

 and pressing the 

Open miniweb 

button.

If the Miniweb exists the page will be opened. If not, the status page 

will be displayed (which is also available by opening the 

<IP_address>/status.html 

address).

The Factory Default Status Page (status.html)

#miniweb #builtinweb #web

The Default Control Page Displayed in a Desktop Browser and in a Mobile Device

 

Summary of Contents for 91540021
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands