Lightware 91540021 Page 47 User Manual Download

Page: 47 / 119

5.SoftwareControl-LightwareDeviceController

HDMI-TPS-RX110AYseries–User'sManual

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

5.9.3.

Front Panel

Front panel tab in Settings menu

Available settings:

▪

Lock front panel

:theFunctionbuttonfunctionallycanbedisabledwiththeoptionismarked.

▪

Dark mode enable

:whendarkmodeisenabled,allstatusLEDsareswitchedoffafteroneminute,ifno

buttonpressed.PressingtheFunctionbuttonbringsbackstatusinfoontheLEDswithoutperforming

the function of the button itself.

▪

Enable default function for Function button

:enablingtheoptionresultsthedefaultfunctionoftheFunction

button is enabled.

#buttonlock #lockbutton #darkmode

5.9.4.

Backup

Details about this function can be found in the

ConfigurationCloning(BackupTab)

section.

5.9.5.

System

System tab in Settings menu

ThreefunctionsareavailableunderSystemtab:

▪

Download system log

-savingthefileofthedevice.

▪

Load factory defaults

- recalling factory defaults settings and values. All factory default settings are

listed in the

Factory Default Settings

section.

▪

Reboot

- rebooting the system.

#log #systemlog #factory #restart #reboot



 



Summary of Contents for 91540021
























































































































Search results

Summary of Contents for 91540021

Reviews:

Related manuals for 91540021

Brands by name

Popular brands

Lightware 91540021, User Manual

Search results

Summary of Contents for 91540021

Reviews:

Related manuals for 91540021

Brands by name

Popular brands